Skip to main content

New Beam Antenna Installation at N6QW ~ FINAL INSTALLMENT!

The Final Piece - Post Mortem!

 
My dream beam is up and operating and I surely can tell the difference! The front to side and front to back attenuation is very evident and I have netted quite a few contacts running 100 watts with my ZIA transceiver on 20 Meters. The signal reports are very good even with crappy band conditions so all and all I am a happy camper.
 
The cost of this installation --well I stopped counting after $2300. The mast with accessories and delivery was close to $800. The beam with shipping was $500 and the rotator with free shipping was $300. The coax and rotator cables were $250. The US Tower base plate with shipping was about $100. The Home Depot hardware was $100 and the contractor was $200. That is a lot to spend for a beam that ostensibly will be used during the down part of the solar cycle. But given where I am age wise this is probably not  all a bad decision. For about another $1000 I probably could have had a 40 foot tower and a three element beam. But never look back.
 
Some lessons learned:
 
  1. The information from the manufacturers is not very good or not even present. SpiderBeam does not have an instruction manual! Given that I am bottom rotating the mast I was told very few are sold for this purpose especially in a fixed location installation thus no manual. I did receive good factory support when I asked about drilling the mast for the bottom mast to rotator adapter and how to route the coax from the beam -- however, this should be standard information and not require emails to the factory.
  2. Yaesu (I am using Model G450) has a standard calibration process for zeroing the rotator so when you are north the beam is actually pointing north. However there are several steps which are not clear and I had to call the factory -- and sort of got "Oh yeah we get calls about that all of the time." So I am not the only one.
  3. I purchased a Mosley custom beam the Model MP-32-N which has the high power driven element from a TA-32 and the lower power reflector from the TA-32- Jr. The instructions are for the most part are OK except for three items. 1) There is an anti-corrosion compound that must be applied to all metal to metal mechanically connected parts. The only place this is mentioned is on the pictorial assembly drawing. The actual assembly instructions about fit Tab A into Slot B are silent on this matter. So if I had not spotted the note on the pictorial drawing my install would have lacked the compound. 2) Routing of the coax from the beam. I called the factory and inquired about a choke balun. I was told that is a really good idea and was given the dimensions. So why is not this just standard practice to say build a choke balun? Actually using the balun facilitates routing of the coax. 3) Where to place the boom to mast bracket? The parts are color coded and one of the final instructions says align the boom to mast bracket with the black index marks on the boom. Mine didn't have such marks and so I called the factory and was told it should be in the middle at the balance point (36 inches). The word balance point rang my bell! The driven element is heavier given the larger traps and size of tubing. So the balance point has to be closer to the driven element. I used a crude mechanism to create a balance structure ( a couple of stacked  1 X1 "'s ) and moved the boom along the balance beam until I found the balance point --which is 28" from the driven element. So why isn't that information in the assembly instructions?
This will be the last post on my antenna and future posts will concentrate on the Simple-ceiver.
 
Thanks for riding along!
 
73's
Pete N6QW

Popular posts from this blog

2019 ~ What is the simplest homebrew SSB Transceiver that can be built?

4/27/2019 The Future of our Hobby is Here! Forget those simple rigs with homebrew crystal filters, cranky IRF510's and the analog VFO's. SDR is the wave that is building strength just like a Tsunami. With the Soft Rock V6.3 SMD Version + RRPi2 With the Omnia SDR and RPi2 Pete N6QW How Simple & How Cheap can you  build a Homebrew SSB Transceiver? 4/26/2019 --- I just converted my websites from an obsolete Windows Based Server with GoDaddy to their cPanel (Linux). This was a cost issue as a one year renewal of the Windows Server would buy three years on the cPanel. GoDaddy is discouraging the use of what they call the Obsolete Windows System. So I had to migrate and reload the whole pastapete.com, jessystems.com and the n6qw.com sites to the Linux based servers. Some files and links got lost in the translation --so you might not be able to see everything! Essentially I have  to open every link to verify that it works --that may take some time

New Technology for 2020 ~ The Hermes Lite 2.0 SDR Transceiver

  The Hermes Lite 2.0 SDR Transceiver. November 7th, 2020 ~ It's Settled! It is done! The stain of the Trump era is soon to be removed! Thanks to all who voted. The Voice of the People has been heard.  Congratulations to President Elect Biden and Vice President Elect Harris. Pete N6QW November 3rd, 2020 -- IT WAS THE MOUSE   We all know this is Dump Trump  Day. Go out and vote! It was the mouse! Back in 1999 I stupidly was one of the very first to purchase a Ten Tec Pegasus. Never buy the first batch of a new model.  Touted as the world's first computer controlled radio , actually I think the Kachina 505 was really the first. But the Pegasus was fraught with problems including a trip back to the Smokey Mountains. I was using an older Windows 95 machine to control the Pegasus and that may be a co-conspirator. Well after many calls to TT -- finally someone who has some smarts told me: Fix your station ground, Make all leads short and Buy stock in a ferrite bead company. I did all

The Next Project Updated 10/10/2022! The rubber has hit the pavement!

The Next Project... A 2022 Transceiver. 10/10/2022 My Apologies. It is with regret that I will be terminating any further work on this project. My caregiver duties have over time become a greater time sink and it is almost impossible to build something working only 10-15 minutes at a time spread out over a day. I apologize for not getting it from design ideas to complete hardware. Most likely I have built the last transceiver I will ever build. Thanks for riding along. My website https://www.n6qw.com/  has the pdf of the postings and I will leave this blog page as is. 73's Pete N6QW 10/05/2022 Still Alive! Regrettably my caregiver duties have overtaken any free time so not much progress. But I am hopeful yet this week I will cut at least one board. A PSA from N6QW.  Think of it like Mary Jo has a "crink" in her back and unable to get in the backseat of the 57 VW Beetle. A bit of a setback but not forever.  Seems like the hired caregiver had a small emergency and not able