New Technology for 2020 ~ A Scratch Built Hardware Phasing SSB Rig

A Hardware SSB Phasing Transceiver!

N6QW makes yet another attempt to lure you into the homebrew world!

April 18, 2020 ~ New Posting  Soon!

This thread is getting large and when I post tomorrow it will be on a new posting and contain some updated technical info. So you will want to tune in.

Covid-19 Practical Tips.

I am disciplining myself to lots of washing, not only my hands; but my clothing. So after a stop at the grocery store and after pulling into the garage, I sprayed my shoes with Lysol and immediately took off my jacket and pants and into the washer. Ooops I forgot to put down the garage door so there I was in my undershorts loading the washers. One of the neighbor ladies was passing by and made it a point to say" Hi Pete" Are you OK? To which I replied I am OK. So first tip close the garage door when you are stripping down to your skivvies. Also wipe down the car seat and steering wheel.

Second problem! I forgot that my really nice Sony earbuds were in my jacket pocket so they got washed too. I spotted them in the washer when I moved the pants and jacket to the dryer (I did have pants on this time). 

I was bummed out because they really worked well. So then I thought -- What if I placed the earbuds in a plastic baggie with a heaping teaspoonful of uncooked rice. Boom this morning the rice looks like it had grown a bit and I now have a working set of earbuds.

I have resisted using the credit card for every purchase; but have been buying groceries with cash. (The theory is if you don't have the cash you don't buy it.) 

My process for the cash once I hit the ATM is to place the cash in a plastic baggie and a quick spray of Lysol and then  seal the bag. I wait 24 to 48 hours before opening the bag. This may be likened to when the teenage boy hears from the gal that she is safe; but he still uses protection. There is conjecture about the safety of using cash -- I hope at least my cash has been sanitized.

I must question if the emperor (with a small e) is attempting to incite civil war by his tweets on liberating states. He is only inciting his base and this approach will likely cause grave harm. Is it now time for the good guys to be counted? Want a metric --- look at the rise in gun sales?

73's

Pete N6QW

***********************

April 17, 2020 ~ A Giant Step Forward!

A kind soul (Mike) took pity on me and reworked my feeble design into a workable circuit that gives a flat response across 270 to 2700 Hertz with the required 90 Degree phase shift. I wouldn't have found it in a million years. And so to Mike: "When you know stuff you can do stuff"

The Plot at 2200 Hertz --- nice!

I will now build this circuit and run some tests to prove the design. This is a major leap forward. Thanks again Mike!

BTW the emperor (with a small e) has no plan to ramp up testing across these United States. His neglect may result in your death. Think about that if you voted for him! 

73's

Pete N6QW

*************************

April 16, 2020 ~ Still noodling circuits.

The 2Q4 was a marvel 70 years ago but am not so sure today. I see some issues with low frequency response and have even moved away from the Modem Transformer coupling. I have spent two days with the LT Spice simulations and cannot see any light at the end of the tunnel.

I see the emperor's ( with a small e) approval rating has dropped by 6 points in just a month. I guess he won't tout that when he blabbers at the daily briefings. 

Take stock when more people get infected and die because of his ill conceived plan to open the country -- his ratings will plummet. It is time to jump ship! The lack of leadership is obvious -- perhaps he may lack leadership gene's! #TOT

****************

April 15, 2020 ~ Part II Quadrature Audio

I took some photos of the Quadrature Audio Plots of the 2Q4 Circuit Simulation at four frequencies: 270 Hz, 300, Hz, 1000 Hz and 2700 Hz. The amplitude and 90 Degree Phase Shift look pretty promising in the simulation. But the real proof is a hardware build and the actual physical testing. 

I reset the inductance value of the simulated 600:600 Modem transformer to a value at 1000 Hz which if you solve the equation for Xl = 2*Pi*F*L where Xl = 600 and F = 1000 you are left with L which is 95.5 Millihenry.

This is the plot at 270 Hertz.

This is the plot at 300 Hertz

This is the plot at 1000 Hertz

This is the plot at 2700 Hertz

There are some observations that will require further analysis and evaluation. From what I see the equal amplitude of the two plots at a specific frequency is governed by the adjustment of R5/R6 which simulates a 1K trim pot. I do note that it is about a 75% to 25% ratio. I can't explain that. But it does seem to hold over a 10:1 frequency range such as 270 to 2700 Hertz.

Next is the shape of the sine wave -- it seems to hold true over the audio range (some early simulating presented a skewed sine wave). The same appears to be true relative to the 90 Degree shift. But, when we have hardware we can actually test how true is the phase shift over the audio range. Based on some comments I have read --I should not hold my breath or maybe that is the case.

Constant Audio Frequency Gain Level over the 270 to 2700 Hertz frequency range may be an issue. The 2N3904 amplifier started life as a microphone amplifier that was peaked so it would have a better response at the low frequencies and to remain flat for the rest of the curve. Late Info: I have been doing some experimenting and have an initial approach that gives only a 7 mv Peak difference between 250 Hertz and 2700 Hertz. That should improve the "presence" factor. Will post that schematic tomorrow.

Since we want to be certain this rig passes the 40M FLEX Radio SDR police criteria of having audio presence and not "yellowy" at low frequencies, I am still wrestling with that issue. A cursory look at the gain levels show less gain on the low end (270 Hz) versus what you see at the higher frequencies (2700 Hz). This is on the order of a couple of hundred millivolts. 

The good news is equal amplitudes and what appears to be a tracking phase shift. The bad news lower frequency gain levels.

We must hold the emperor (with a small e) responsible for the 610,000 Covid-19 infected citizens and the 30,000 deaths. He did not score a perfect 10 in his response! #TOT

 

73's

Pete N6QW

******************************

April 15, 2020 ~ Quadrature Audio from 2Q4

I coupled the output of the first audio stage into the simulated 2Q4 and got two signals 90 degrees out of phase. The amplitude of the signals is adjusted by the pot shown as R5, R6. I had to adjust that pot (changing values) to give a fairly flat amplitude over the range of 300 to 2700 Hz. This took some diddling and involved making the 500 Ohm pot into a 1K  pot. A combo of fixed and variable resistors can give a fine adjustment --two 200 ohm resistors in series with a 600 Ohm trimpot would work. I also had to limit the signal input to no more than 500 mv.

Later I will publish a more detailed photo of the circuit and the two plots -- The second trace is blue and hard to see but they are indeed 90 degrees out of phase. Super progress. 

Now what I haven't investigated is the angular shift from 300 Hz to 2700 Hz. Amplitude looks ok but haven't evaluated any phase shifts. If I did this in hardware with an audio oscillator -- I could look at the Lissajous figures from Ports A and B on my Rigol Scope.

Each day it is more obvious that the war against the Covid-19 is being fought by individual states with science, metrics and input from the professionals. The WH briefings are irrelevant!  Look to those  Governor's on the East Coast, Mid-West and West Coast to lead us, to keep us safe and to see us through this. #TOT

73's

Pete N6QW

April 14, 2010 ~ Homebrew 2Q4

We have a Constitution not an emperor or king!

So Ok the Model 2Q4 Audio Phase shift network is long in the tooth having observed it 70th birthday! It is also marginal by today's standards maybe achieving a maximum of 35 dB of opposite sideband suppression. Yes it was advanced technology for 1950 but today is can be likened to doing brain surgery with a rusty spoon. 

It is a fairly simple circuit and so the "illuminati"   would say --Too simple and thus no good. Sort of like to the Wright brothers --that bicycle won't fly!

Many would say -- you are wasting your time and you could do it with Tayloe detectors and polyphase networks. On the rare occasion that I actually removed my EMRFD from its position as a book end and in looking through section 9.32 or was it 9.23 I noted how the authors approached the subject. They simply categorized it by dB of suppression. If you want 20 dB then do this and if you want 60 dB then do this. 

Now that made sense to me in a slightly different light. Suppose you just wanted to experiment and as a first goal build a phasing transmitter. Then as a next goal measure the sideband suppression (hey that would be novel). Finally as a third goal tinker with what you have to see the real limits of what you have built -- you know what makes things better and what makes things worse. 

This is a learning journey --what else are you going to do while hunkered down? A polyphase network has tons of parts whereas the 2Q4 has 8 parts!

Now as I have found in the past with many of my projects, many modern hams are basically lazy! So to remove that excuse I have collected the part numbers from Mouser for what is needed to homebrew a 2Q4. In most cases there are specific part numbers for the exact component specified (like the capacitors) but in other cases such as the resistors you might have to add a couple of values. 

Here is an example a 770K Ohm 1% resistor is specified. Well I was able to find a 768K 0.1% and a 2K Ohm 1% so added you get 770K Ohm at no worse than 1%. In the other case a 198K Ohm is specified and I found a 100K Ohm and a 97.6K Ohm which would get you to 197.6 at 1%. 

Now keep in mind this network and the component stability in 1950 gives you a 90 Degree shift with a 1 degree tolerance (crude by today's standards). But keep in mind many of our rigs have homebrew crystal filters that are less in performance than a commercial filter; but we still use them.

Now if you would like a list of the Mouser P/N's then email me at the  address above. I am doing it this way to gage the interest in this project. Yes, that would be asking too much to email me so...

It was fun to watch the emperor (with a small e) melt down yesterday. That "stable genius" is going to get us all killed! Noteworthy is the real leadership being demonstrated by the 15 or so Governor's who have formed coordinated alliances that rely on metrics, science and the advice of the healthcare professionals! #TOT!

*******************************

April 13, 2020 ~ More on the Phasing Rig

But first a PSA. 

If you stand with Trump; man you are in the wrong line! If he opens the US before it is an appropriate time we all are at risk of a certain death. People are saying the Trump Properties are tanking and this may be coloring his decisions.

My plan is to build a TransReceiver Phasing Rig. For the unwashed this means a separate transmitter and separate receiver that share a common link -- The Phased LO. This will be done with  the 2Q4 on the transmit side and the QRP-Labs Polyphase network  on the receive side . So a bit more hardware but a starting place. 

I am aware the opposite sideband rejection for the 2Q4 on a good day and when all of the planets align is only about 35 dB so the 40M FLEX Radio SDR Police will have some fun; but the journey of 1000 miles starts with the 1st step.

I took the 600 Ohm Impedance of the Modem Transformer and solved the equation for "L" at a frequency of 2000 Hz. That value was 48 mH. Next I looked at a Transient plot of the output across the Combo of R5+ R6 to simulate a 500 Ohm pot with the center wiper to ground. Test changing these values so that the sum is always 500 Ohm. Really neat to see the plots at the test points are 180 Degrees out of phase and of equal amplitude.

This design will be repeated for all three amp stages. I bought 10 pieces of the 600 Ohm to 600 Ohm Modem transformers for about $8. The exception is the final two stages do not have the 500 trim pots on the outputs.

73's

Pete N6QW

Easter Sunday 2020.

The 2Q4 Network and solid state audio amplifiers (3X 2N3904) graph paper layout and finished PCB.

Here is hoisting a virtual beer to you to celebrate this Easter Sunday. The beer, San Miguel, is from the Philippines and is potent --especially the kind served there and not the export version. After a short stay in the Philippines, during my naval service, I came to two conclusions: Excellent Beer and Hot Women!

So OK Guys and Gals you are stuck indoors and looking for an activity to fill time while we await the stable genius to come up with yet another really dumb idea like opening the USA too early! Or his hawking medicine with no license to do so.

So how about a hardware based Phasing SSB Transceiver? I have seen hardware based Phasing Receivers from KK7B (Rick Campbell) and in the transmitter department we have the GE SSB Junior or the Central Electronics 10A and of course the drifty HT-37 (at least mine did).

I am exploring several possibilities. My two Polyphase Phase Shift Networks arrived from Turkey (Hans Summers) as well as a real "Oldie" the B&W Model 350. I also have a slug of Tayloe Detectors coming.

My first thought is to couple the B&W Model 350,  2Q4 network with the RADIG V.2 board as an experimental transmitter. The 2Q4 would provide phased audio which would be coupled through Modem Transformers. A small relay could redirect signals so we could have selectable LSB or USB. OR as was pointed out to me by my good friend in VK land (Greg) if you switch instead the CLK0 and CLk1 into the ADE-1's -- an instant sideband reversal. I personally verified this so we have two ways to select LSB or USB modes of operation.

http://www.n6qwradiogenius.us has some additional circuits we would use.

This is a starting place and we will employ the phased Si5351 LO. For the receiver there may be a Tayloe detector hiding in the bushes.

In one of the ARRL SSB handbooks Richard Taylor W1DAX presented a design for a solid state phasing SSB transceiver. Need to dust that off. [This is when ARRL built stuff versus selling expensive radio hardware.]

Stay tuned and start thinking about parts! There, that may help erase the stupid stuff we hear from the daily briefings. 

73's
Pete N6QW

New Technology for 2020 ~ A Trip Back in Time

A 1930's 6V6 CW Transmitter!

Who in their right mind or at least having a semblance of sanity would ever think of building a 1930's style QRP CW Transmitter? Well that is the whole point -- keeping our sanity during the HUAH (Hole Up At Home) adventure. So in an effort to stay sane I finished something I started several months ago. 

It was a thrill to hear that warble toned, chirpy, key click signal coming out of the nearby receiver. Today I might venture out on the Reverse Beacon Network to see who  is hearing my mighty 10 watts. Firstly though are a few more checks to insure a purity of signal and that indeed there is adequate filtering so that I am only transmitting on 40M.

Travel with me as I fabricated this 10+ Watt jewel. Hopefully you can see this was not a 2 hour or one and done effort. It took a lot of planning and fit checks. I used a lot of graph paper to make layouts and to check parts placement. 

This is what 60+ years of experience is all about. The very last thing you do is heat up the soldering iron. I also used tools like LT spice to simulate the Pi Network Output and that was most useful. Interesting note -- you can plug in a 6L6 into the socket for a bit more power output. But that is like using  a sledge hammer where all that is needed is a tack hammer. Rather than re-invent the wheel I started with the Ameco Circuit which shows up all over the Internet?

Now the question becomes -- would I put it on the air?  The answer is doubtful that I would. This project was just a time filler and now time to move on with bigger fish. It did help my mental health and was fun to plan and execute; but speaking with another ham one letter at a time is not my idea of communication. 

I do however have an appreciation of what the hams of old had to do to get on the air. There were no credit cards, eBay or Amazon or computers to instantly have parts show up on your door step. These hams were innovators, scroungers and had immense creativity.

Yesterday I saw a pitiful posting on the Bitx reflector where a supposed experienced ham wanted to know if the green wire that was to be attached to the left side of a pot--- was it the left side facing you or the left side away from you. 

Today it is easier  to post on the reflector and be told the answer (which I found on that reflector are not always correct) rather than look at the schematic, check the board wiring and think about the CW CCW control aspect. That is where you learn. The hams of old would just know which left side!

73's

Pete N6QW

New Technology for 2020 ~ The ZL2CTM Teensy 3.5 SDR Rig

ZL2CTM Teensy 3.5 SDR Rig - More!

The Teensy 3.5 and RADIG V.3 Are Alive!!!!!

 RADIG V.3 & Web SDR

3/10/2020 ~ St. Paddy's Day --a  Week Away!

So OK  a small drift into the Pasta Pete mode then back to SDR.

My XYL is part Irish (and no part Italian --if she were part Italian we'd probably would have killed each other by now) and loves her traditional Corned Beef and Cabbage St Paddy's Day dinner. 

There is a trick to cooking this meal entirely in one large pot. You must have the small white Potatoes, Cabbage Wedges, Carrots and of course the Slab of Corned Beef. Did anyone mention garlic? One year this celebration involved my cooking for 12 guests. 

For that dinner I bought a 12 pound slab of Corned Beef from Katz's Delicatessen in New York and had it air shipped to Seattle. That cost me about the price of a Ubitx V.6 with all of the bells and whistles. But hey, it was for the wifey. After dinner I looked for left overs -- there were none. It was that good.

There was a Romance Comedy movie about 25 years ago "When Harry Met Sally". Part of that movie was filmed in Katz's Deli. I have also eaten at the Deli and it is indeed superb. So if you are looking for some authentic Corned Beef --they have a website and with plastic in hand you can have "real" Corned Beef at your St Paddy's Day Dinner! There is time to order one; but the window is rapidly closing.

Funny story with that Corned Beef and New York. When the box arrived --sure enough it was one huge slab. Not wanting to screw this up, I called the Deli and asked to speak to someone about how to cook this jewel. One of the staff shared that indeed it was a good idea to cut the slab in half so it all gets cooked properly. 

The day following the dinner I called Katz's Deli and asked to speak to the manager. This grumpy, grizzly guy gets on the phone and in typical NY fashion starts off by saying "What do you want to complain about?" 

I quickly said No, I want to thank you and your staff. They were so helpful and the Corned Beef was totally consumed and nothing left -- 12 people ate 12 Pounds of Corned Beef. It was excellent! He then says --Nobody Calls to Thank Us --and hung up. Well that's NY. 

Back to SDR. ZL2CTM's winning design continues to garner excellent signal reports. So visit Charlie's you tube channel and learn how to build this amazing radio. No computer needed and if you feel the need to see your waterfall --tune in one of the web based SDR receivers. I did that just to look at the sideband suppression on the opposite side band. 

I have made about three dozen contacts so far and it has performed well. I am indeed impressed! 

Some of my future posts will be about how I stumbled through the Iowa Hills Software and the results of the filter changes. ( A note to Bob, you will probably want to tune out this part.)  

I want to test filters of various band widths such a 6 kHz (AM Receive), 2.8 kHz, 2.0 kHz and maybe even 600 Hz. Just thinking ahead -- a selector switch with four positions, and a two digit decode so  two Teensy pins could result in 4 band widths. Now how cool is that? 

Oh something else ZL2CTM shared with me during our Skype event. He asked if I had looked at the AD9833 DDS board. I said no. This is a really small DDS board and is only good to 12 MHz but just think for a minute -- those radios which use a 5 MHz VFO or PTO. 

In fact a couple of my Ten Tec Radios including a Ten Tec Omni C that has a drifty PTO. This TT radio brings the PTO signals out to a jumper on the back panel so you can fit a Remote VFO to this radio. Wow you wouldn't even have to mess with the radio. Pull the jumper plug and fit the AD9833 output into the Omni C. Charlie buys these for about $1.50 for the complete board. Amazon has them for around $4.

In doing a bit of research on the AD9833 --one homebrewer directly soldered the AD9833 to the back side of an Arduino Nano as the pins needed for the AD9833 all aligned that way. Man that was really small. He added an OLED display and in the palm of your hand a complete Frequency Generator good to 12 MHz and it would even work with your Bitx40.

2020 and yet more technology for us!

Remember scrub your hand just like a Democrat that shook hands with the emperor (with a very small e) as one precautionary preventive move in the stemming of the spread of COVID-19.

73's

Pete N6QW

3/9/2020 ~ A Conversation with ZL2CTM

There is nothing like a bit of face to face time to clear the cloud of smoke surrounding what you are doing. Regrettably some of the smoke was from my burning parts.

Yesterday I got an email from Charlie, ZL2CTM suggesting we Skype. You have got to love this advanced technology as we were able to do just that. 

Firstly, I discovered that I had been "dabbling" with the wrong version of the Iowa Hills Software. There are several different forms (all good when used properly). Seems like I have been using the general purpose set of filter design hardware and what you really want is the Hilbert Transform (HT) Variant. 

The HT math operators have been around for a long time; but have become a staple for digital signal processing. Since we are not using DDC but the I and Q method then the In Phase (I) and the Out of Phase Quadrature (Q) signals coming from the two ADE-1 Direct Conversion receivers are separated by 90 degrees. The mathematical processing ongoing in the Teensy 3.5 recognizes and processes these 90 Degree out of phase signals using the Hilbert Transforms.

But to do this you must have the HT processing be designated in the sketch. Thus the Iowa Hills Software  generates these two sets of math operators one of which is at 45 Degrees phase added and the second is -45 Degrees phase added. Thus with the + 45 Degrees  and - 45 Degrees the span is 90 Degrees. 

This realization, a result of my conversation with ZL2CTM led me to the Hilbert Transform Software within the Iowa Hills Suite and we now have a filter that looks like what is shown below. In a contra approach to the many Commercial Box operators, I have set the bandwidth to around 2.4 kHz whereas the FLEX guys seem to like 2.8 to 3 kHz so their signals have "presence" and are not yellowie!

Now I need to collect the two sets of coefficients and embed them into a Teensy 3.5 sketch. For this 1st test run I will be using 100 coefficients and if my "dabbling" works, then I will test drive more coefficients. 

In theory more coefficients add more points to the curve and this provides a better  defined filter. The question remains. How many is enough before you reach the law of diminishing returns.

A big Thank You to ZL2CTM for suggesting we Skype -- Otherwise I would have been in the weeds for a very long time.

Stay tuned for the excitement. 

Coronavirus Tip: It is important to wash your hands in a manner just as if you were a Democrat and were forced to shake hands with the emperor (with a very small e). Special note:  it is more than just a quick rinse, it is a thorough Scrubbing!

As an aid Sing Along like Ensign Nellie Forebush in the movie South Pacific "I'm going to wash that man right out of my hands". Several chorus loops through that song is about the right length of scrubbing!

73's

Pete N6QW

3/8/2020 ~ The 2N3866 Bi-Directional Amp!

PWKSCDS

***************

3/6/2020 ~ 1St Contact with W7LTG, Francesca at 1314 PST on 7.204 MHz -- My report: 5X9 + with good audio ~ Running  100 Watts. I may try to work the contest this weekend. You just got to love this technology.

2nd contact with WV6PBJ, Dave at 1400 PST. We are on a roll.

Worked some of the DX Contest including a XE2, 4A7S, TI7W, KH6, TO3 (Guadeloupe), PJ4G and JA3YBK . We are indeed on a roll. I was running 600 Watts --this contest is not for the QRP kids!

I will be further testing the opposite sideband suppression. But significantly the RADIG V3 Main Board and my bi-directional 2N3866 RF Amp board are doing very well.  

BTW the RF Amp stages following the Band Pass Filter on the RADIG Board are a 2N3866 steerable amp and following that is a 2N3866 Driver Stage and the Final is the IRF510. This lash up produces in excess of 5 watts. The amplifier following the RADIG is the CCI AN762. The antenna is my inverted V with a 35 foot apex.

Ugly and Al Fresco but works!!!!!

This morning I spent some time with the Iowa Hill Software and defined a 7 Pole Chebyshev 

Band Pass Filter comprised of 127 Coefficients. This filter is only 2.4 kHz wide and looks like this. It looks like a Brick Wall.

In "diddling" with the software my first run was to set the 3 dB point on the low end to about 250 Hz and on the high end to about 2650 which effectively make the 3 dB bandwidth 2.4 kHz. At 60 dB down we are around 3.5 kHz (thus my brick wall comment). But until I actually load it into the software and test it I won't know the "real world" performance. 

This was essentially my 1st run at seriously using the Iowa Hills Software so I really may be off in the weeds. I am just at the learning stage and the seasoned pro's are likely having a good laugh. 

I have the coefficients but I think in the ZL2CTM software you have to have two sets of filter coefficients so that the other is 90 Degrees from each other. Need to study that but from what I inspected in ZL2CTM's code that appears to be the case.

I dumped the 127 coefficients into an Excel Spreadsheet but have not figured out how to make a second column where the first series of points is simply inverted. I have been doing it by hand --it may take a while to cut and paste all 127 values. But that is only half the task, as you must precede every one of the values with an identifier in the Arduino code. So that is 254 entries. It may take a day or two for me to get it all done and test drive it.

Here are the 127 coefficients:

-0.00145151
-4.65E-04
4.33E-04
0.001329462
0.002258667
0.002865166
0.00259709
0.001081036
-0.001858205
-0.006391743
-0.012684756
-0.020735604
-0.030317289
-0.041010182
-0.052191803
-0.06303164
-0.072575248
-0.079856866
-0.083980378
-0.084209883
-0.080081336
-0.071477129
-0.058650131
-0.042229236
-0.023195131
-0.002799094
0.017553243
0.036424438
0.052479742
0.064627489
0.072130783
0.074675596
0.072402618
0.065894145
0.05610445
0.044249241
0.03167521
0.019715506
0.009544312
0.002057282
-0.002208487
-0.003115033
-9.18E-04
0.003787228
0.010160715
0.017227087
0.024000243
0.029603667
0.03336817
0.034896403
0.03409305
0.031156935
0.026534562
0.020846461
0.014799533
0.009093628
0.004333681
9.62E-04
-7.85E-04
-8.87E-04
4.67E-04
0.002926969
0.006032333
0.009282744
0.012202263
0.014399063
0.01560802
0.015713103
0.01475021
0.012890381
0.010405788
0.007625942
0.004891207
0.002508133
7.12E-04
-3.56E-04
-6.59E-04
-2.61E-04
6.90E-04
0.001993799
0.003420847
0.004750315
0.005795487
0.00642559
0.006577244
0.006255898
0.005528736
0.004510053
0.003341293
0.002169768
0.001129063
3.23E-04
-1.86E-04
-3.80E-04
-2.83E-04
4.70E-05
5.26E-04
0.001063346
0.001569604
0.001971346
0.002217828
0.0022856
0.002178341
0.001923024
0.001563585
0.001152894
7.44E-04
3.84E-04
1.06E-04
-7.14E-05
-1.46E-04
-1.30E-04
-4.55E-05
7.85E-05
2.13E-04
3.31E-04
4.15E-04
4.55E-04
4.48E-04
4.02E-04
3.29E-04
2.43E-04
1.59E-04
8.75E-05
3.65E-05
7.56E-06

-2.37E-06

My eyes hurt...

73's
Pete N6QW

In unrelated news.. Mick is gone and are what people saying true that Mikey may be replaced by Nikki?
The emperor must be pissed.. Coronavirus has shown up in Florida and New Jersey and that is sure to impact his golf game! 

********************************

3/5/2020 ~ SEABEE Birthday -- 78 years ago the SEABEE's were formed ( 5 March 1942). So to all SEABEE's world wide, present and former --Happy Birthday -- Can Do!

WG5EEK posted a nice video on you tube about SDR Dongles -- again something that just showed up on my phone. 

There is some really sophisticated software floating around and one lets you have what is in essence a "super scanner" all for $20. 

There is another piece of software called SDR# that had a very nice spectrum and waterfall. 

So like "quickly" rather than slowly but surely, -- SDR is finding its way into our hobby. Most of the software is Windows based but some is also dual Windows and Linux (like Quisk). I am finding a whole new world with software that is Linux based.

3/4/2020

[New additional video of the transmit waveform just posted.]

My initial posting of this morning described some issues I was having in making the transition from receive to transmit and back to receive. 

That configuration used a DPST relay which switched 12 Volts between receive and transmit. On receive the switched +12 VDC was only switched to the audio amp stage. On Transmit at least 4 relays were involved to add voltage to the transmit circuits and to steer signals through the bi-directional amplifier stage.

There was a considerable amount of back EMF and despite having some snubber diodes -- even the Si5351 jumped 100 Hz in the transition. NOT GOOD MY FRIEND!

The remedy was to permanently connect the 12 VDC to the audio amp stage as the muting in the software takes care of that issue. 

For the transmit side -- an old trick. The switched voltage is run through an LM317 Voltage Regulator. On the input side is a 100 NF cap and on the output side is a 1 Ufd electrolytic. From the V Output to V Adjust is a 220 Ohm Resistor. To that junction is connected 1820 Ohms to Ground comprised of a 1K and 820 Ohm in series. The LM317 Calculator says with these constants you should get around 11.5 VDC. 

Now the problem is gone and the supply to the Teensy stages is clean. No longer does the Si5351 jump in frequency as you transition. 

This is a video using my new 12 MegaPixel Camera acquired from Amazon for less than $10. There is no audio and I am using the Linux Mint shop computer with the program Cheese. 

The transmit signal is raw coming out of the bidirectional amp stage (single 2N3866). With a bit of additional filtering we should be good to go.

Don't you just love this technology -- another event in 2020. 

I am having some issues making this radio transceieve. This same Teensy 3.5 board was used previously and worked FB.

It will work receiving and like wise transmitting but upon return to receive it is like the transmitter is transmitting into the receiver. Not good.

I may have corrupted the code as there are provisions in the code to efficiently handle this transition. Another possibility is some of the relays may be hanging up. More investigation needed.

The receiver is picking up some DX --must be a contest coming up this weekend.

Just when you thought you escaped commentary on the Coronavirus, a friend sent me this calling it "The Redneck  Coronavirus Cure"

Spray in mouth liberally and often.

Might  not help, but at least you won't care!

73's
Pete N6QW

New Technology for 2020 ~ The ZL2CTM Teensy 3.5 SDR Rig

An SDR Radio In a Microcontroller.

3/3/2020 ~ Problem Solved 

A cure for Coronavirus? Hey Mikey are you watching this blog? 

My Calabrian Grandmother had a bag of old folk remedies that were not many by count; but did cure a variety of illnesses. When I was about 8 years old I got some sort of rash on my arms and despite seeing the doctor it would not go away. 

It was summertime and as kids do I was scratching and picking at the scabs --it got worse. By chance we were visiting with "Nonna" and she immediately said: I know how to fix that! 

She made a poultice out of beaten eggs and flowers of Sulphur and spread it over the infected area. Next she ripped up an old soft bedsheet and covered the area in what looked like a mummy wrap. Her stern words: leave that on for 24 hours! Boom the next day I removed the wrap and the rash was gone!

When I next saw my Grandma, I showed her my arms and she said "good". I then asked what was that stuff. She replied --I don't know; but this is what we did in the old country when people had rashes. Thinking back --it must have been a crude form of a sulfa drug. But I do know that Flowers of Sulphur as far back as 2000 years ago was used to treat skin conditions. "Nonna" knows Best!

So "Nonna" I am sure has a cure for Coronavirus using Italian Penicillin.

If it were only that simple...

A Message to Mikey: Don't discount any possibility for a cure. 

***********

Problem Solved...

Firstly all due credit to Charlie Morris ZL2CTM and his pioneering work in developing an SDR Radio in the form of a Teensy 3.5 microcontroller. I first saw his work nearly three years ago and Charlie, a true gentleman, readily shared his code and schematics with me.

[ZL2CTM has now moved up to the much more powerful Teensy 4.0 (about 5X the power of the Teensy 3.5 in terms of processor speed) and the use of a very nice 240 X 320 Color TFT display. ]

I did add a few bits and pieces to his original work; but never quite achieved the results he did with the Teensy 3.5. It was at that point that I branched off and took the RF hardware parts and mated those with a Raspberry Pi2, Pi3, the ASUS Tinker Board and now a Linux Mint 64 machines. All of these several implementations use the Quisk Software from N2ADR. This approach has been documented on my website at www.n6qwradiogenius.us

The acquisition of a Teensy 4.0 prompted me to go back and revisit the Teensy 3.5 implementation, reasoning that I should really get that that to work first, before heading off to the Teensy 4.0. 

I was 100% sure of the RF hardware as it has been used with the Single Board Computers and the "Big Dude" Linux Mint 64 machine. So now the focus is the Teensy 3.5 and the CODEC Board and the all important ZL2CTM's code.

Dusting off the original Teensy 3.5 and CODEC Board I managed to smoke both which once again proves haste makes for waste. I had a spare Teensy 3.5 and a CODEC board which were recently installed in my original PC Board assembly. The results were not unlike what I saw two years ago. 

My earlier experience identified that there were issues with opposite sideband suppression on very strong signals. These prior tests saw this condition on receive and transmit.  When I transmitted on it, the 40M SDR police shouted at me that here was a component albeit not as strong, on the opposite side band. At that time I had conferred with ZL2CTM on what I saw; but he did not see this issue on his set up. So what ever it was the issue was only being seen at N6QW.

It is so nice when you are able to replicate circuit performance and here we were again. The same problem of two years ago was documented in the recently posted video which is now on you tube.

But yesterday I changed the Hilbert coefficients from 70 in the older code I was using and replaced those with the 100 coefficients found in Zl2CTM's latest code used with the Teensy 4.0. 

These coefficients come from the FREE Iowa Hills Software program that essentially define the digital filter curves (they have variants for Low, High and Band Pass Digital Filters). I believe the original digital filters were either 2.7 or 2.8 kHz. 

I also took another look at the Teensy 3.5/CODEC board just to make sure all was snug and tight since I had just replaced the Teensy 3.5 and the CODEC Board.

The Moment of Truth arrived and the above video shows the results. The issue seems to have ben resolved!

*******************

People are saying we are in a #Trump Slump so keep this guy shown below in your prayers. Your life may depend on him. For those of you who may not know this man, he is the Coronavirus Czar designated by our emperor (with a small e) to take charge of the US response to this terrible global scourge. 

We now have a statistically significant number of cases with many newly identified this past weekend. People are now saying that there are likely six deaths in Washington State associated with the virus.

These USA cases represent a turning point as a large number of the infected individuals did not travel to the Far East nor were they in direct contact with known infected persons. The CDC uses a clever term calling these instances  "community based" meaning the cases just sprung  up in the community. 

It is also posited that the cluster of infected individuals in Washington State may have been exposed as far back as 6 weeks ago. The disease vector will undoubtedly escalate in a geometric progressive fashion much like the rabbits in the famous Fibonaci sequence versus a simple linear expansion .

I have a package of parts in my garage that were shipped directly from China to me. I may never open that sealed bag!

What will happen if the Coronavirus shows up in Florida or New Jersey.  Imagine for a moment the person that has to tell the emperor (with a very small e) that he cannot visit Mara Del Lago or Bedminster. BTW the first case was just identified in Florida . There goes that planned golfing weekend. 

 The US Chief Responder to Coronavirus.

His Name is Mike Pence and has a day job as Vice-President to the emperor  (with a very small e). 

#TrumpSlump