Monday, April 1, 2024

April 1, 2024. The 2nd Quarter of 2024 is here.

Hopefully those who read this blog survived the assault on the Jellybeans, colored eggs and chocolate bunnies. Needless to say, those who practice dentistry are a bliss with the thoughts of new cavities being formed arising from the Easter holiday.

But we are here to talk about amateur radio and so we must begin. I was asked a question the other day on why I was such a Debbie Downer on Nano VNA's. 


A recent post had this photo above showing the plot of a four-pole crystal filter I built and tested using my Nano VNA. This plot told me a lot. But behind the plot itself was a knowledge base of what the plot should look like after following the design process.

My issue with the Nano VNA is that it is nothing more than a tester (assuming its calibrated, working properly and the test setup has a load on the DUI) that depicts the response of what actually exists. In the plot above I can see that there is a good match to the filter by the flatness of the pass band, that it favors LSB by the slope of the curves and shape factor that with the wide skirts is as broad as Mary Jo. Will it work in a circuit? Yes! Will it be good on CW? Likely No!

The Nano VNA's use as a design tool is limited to physically changing hardware and then making a run and reporting that result. That takes a lot of valuable bench time. 

If we move to Band Pass Filters, then an approach I prefer is to simulate the filter in LT Spice where its use as a design tool enables me to look at the pass band frequencies, the shape of the filter and the all-important section coupling capacitor. Changes are quickly done with a click of the mouse, and you don't need a soldering station. 
 
 
 
 
 
 Simulation with 1pF Section Coupling Cap.
 
 
Simulation with 5pF Section Coupling Cap.

Simulation with 0.5pF Section Coupling Cap.

Having done this simulation over and over you soon recognize the pattern of a double hump response means the section coupling cap is too large and making it smaller results in a flat top response curve. If that cap is too small you get a narrow, peaked response. The key is that the simulation approach gets you there faster. 

Once built you can then run your Nano VNA to affirm what was actually built is the response predicted. Here is the key point! If the two don't match, then most likely it is not the design but what was built that is the issue. Things like a bad solder or shorted solder joint, a wrong value capacitor or wrong number of turns on the inductor are the issues not the design!

Bare basics: a screwdriver is a poor substitute for a hammer.

Ukrainian Easter Eggs.


Memories of Easter's past. I grew up in western Pennsylvania, where we had large enclaves of immigrants such as Italian, Irish, Polish and Ukrainians. Many came to work in the aluminum or steel factories and coal mines. Of note about the Ukrainians, they hand painted their Easter eggs and these were works of art. I also remember the Ukrainian YL's seemed to physically mature more quickly and were quite hot! Mary Jo may have been Ukrainian!

73's
Pete N6QW

 

Sunday, March 31, 2024

March 31, 2024. Happy Easter to those who celebrate this day.

What a great day to Binge on Chocolate and experience the pain of that filling that has been leaking. 

I would be in that category with the leaking filling(s) had I not just spent an amount equivalent to one of the fancy new uptown appliance box transceivers on two filling repairs. Well at least I can binge on the Chocolate bunnies without fear of pain.

Regrettably everything appears to have jumped in price including the price of parts. Well not so much the parts as the shipping costs. 

That notably is seen in the eBay treasures. I spotted a nice heathkit DX-20 for about $50 and the shipping was $65. Likely it is a twofer with part being a way to in effect charge a higher price by inflating the shipping and in part by increased shipping costs. Shipping with insurance across the US was about $150 for this jewel and that was three years ago.

6AM on the Left Coast ~ 20M Easter Sunday!

My only hope is the cost of Chocolate Bunnies remains steady although a pound of See's Candies for the XYL to mark this day was $40.

Happy Easter!

73's
Pete N6QW 

Saturday, March 30, 2024

March 30, 2024. Chasing a dream!

 One of my cherished boat anchors!


Since 1967 I have owned about eight SWAN SW-120's and this one I acquired about 14 years ago. For those who don't know, the very first offerings from Swan Engineering were three mono-band transceivers covering the 80, 40 and 20M Bands. 
 
This particular unit appears different from many of the single band Swan units and that is because while not in the 1st group of 10 produced (Gold Face) it was in the early builds and built in Benson, AZ. The Swan Net has a keeper of the S/N's, and I was told this one was built in June of 1961.
 
Noticeable is that later units had a Meter Face over the dial readout and this one has a very expensive Triplet meter. The later units had a less expensive meter and the dial cover and the meter front matched. The final is a 6DQ5 and typically you can get 100 watts on Tune. The Balanced Modulator is a RCA 7360. 
 
[AD4DQ on his QRZ page has photos of his vintage gear. Sitting side by side is a photo of two Swan units with one that looks like mine and the other a later unit.]
 
The radio is operational and of note has a linear dial readout and it tunes from 14.2 to 14.235 MHz USB only. A true Transceiver it uses a unique system of biasing the tubes to cut-off when not being used. Certain tubes are biased OFF in transmit and others OFF in receive. A simple 4 Pole DT relay does it all. 

The IF is 5.173MHz and the VFO is at 9 MHz. This topology was pure Genius as it would result in an instant two band rig with the 5 MHz Filter. The additive sum gives USB on 20M, and the subtractive mix inverts the sideband to give LSB on 80M. By shifting the VFO from 9MHz to 12MHz gives LSB on 40M. This is how it is done on the later SWAN SW-240.
 
The Audio Gain control is really the RF Gain Control. Owner mods include adding an AGC circuit and a padding cap to shift the frequency down to the CW bands. Kind of a Kludge!
 
Herb Johnson the founder of Swan Engineering, later Swan Radio, hand built most of the early production units and the silk screening is kind of crude. Much of the early builds were done in his garage in Benson. 

Keep in mind this was Cycle 19, the hottest sunspot cycle to date for ham radio and the other big advantage was size. The home station might be a Hammarlund HQ180 and a Johnson Invader that combined weighed a ton and needed the whole desktop. The SW-120 was light weight and could fit under the dash of a then modern auto in the space between the dash and transmission hump. Yes, I had one mobile in a Chevy Vega.
 
This jewel cost in the $300 range and when a KWM-2 cost $1250 in 1961 -- the price point made it a winner. Shortly after moving his operations to Oceanside, the Swan 240 hit the market and it had all three bands in one box.

One very interesting design note (among many) is that the Transmitter Pi Network is in the receive chain so on receive if you peak up a signal with the plate and load controls --you are close to the values for transmit.
 
Just for fun I once checked into the 20M Collins Net with the Swan 120. What fun!  
 
This SW-120 was in particularly good cosmetic and electrical shape and remains so today.  Too bad it doesn't tune down to FT-8 as that would be a blast. 

Thus, the SW-120 was indeed chasing a dream: DX operation in the car running 100 watts and a small size. Much later the ICOM IC-706 would be a similar dream chase with an even smaller size, no special power supply, multi-band and noise blanker. 
 
Also in my favorite category are the KWM-1's I have. Herb Johnson went on to found Atlas Radio.
 
73's
Pete N6QW

PS About a year ago I bought a SWAN SW-175 (80M) for $50 and it works, and I had thoughts of converting it to 20M by adding an Arduino and Si5351 and put a color TFT in the dial face. As best as I can tell three or 4 coils plus caps would need changing. Currently on eBay is a SW-140 for $200. That is outside my $50 template.

In case you are keeping score...

 Interesting results... Iowa : Joni Ernst's Republican seat was won by Democrat Josh Turek. [senatordb.com] , [ballotpedia.org] Kansas :...