Sunday, April 21, 2024

April 21, 2024. The J310 Dual Gate MOSFET Rig & Soda Bread

So, OK Pete, how do you mention J310's and Soda Bread in the same title without seeming like you are suffering early onset of dementia. Stay tuned and you will find out. 

First the J310's. In earlier blog posts I mentioned I had found a board in the junk box (likely left over from my Simpleceiver project). It had been cannibalized but did have most of the parts in place. On this 4X2 inch board were four J310's (two each for the pseudo-DGM) an ADE-1 and an SBL-1, plus two steering relays. Last but not least, a 4 pole HB Crystal Filter at 4.9152MHz. See the March 27th, blog posting.

The tarnish on the copper board tells you it has seen better days. A different earlier post also showed the LT Spice schematic of this configuration with a 9 MHz commercial filter. 
 
 
Is this a high-performance circuit on par with an Apache Labs or FLEX SDR -- hell no! But for a simple low part count module does it work -- YES!

BTW the audio amp stage in the video was also recently presented in the blog as was the small RF amplifier board as found on Amazon. If you as a reader have been paying attention -- in the background, we have been building a SSB transceiver but perhaps you missed it. The Driver and Final would have the PNP and P Type devices.



 
 
 A representative IF Amp Stage
 
I can see blog readers shaking their heads about J310's connected as a DGM and all that fussing with Super Glue and cutting Manhattan pads. I call such glue and paste activity as drudgery!

Well for your Dining and Dancing pleasure soon you will see an answer to not having to do that drudgery work in the form of a Circuit module with the J310's. The Wizard of Portland OR will soon be sharing some exciting information about the availability of the J310 DGM Module.

With deliberate coincidence you can also find a suitable 4.9152MHz Crystal Filter available from K7TFC's menu of parts.

Hurry to the mostlydiyrf website and sign up for Todd's (K7TFC) newsletter so you don't miss out on this new device.

Of import what we are doing is not a warmed over Bitx design with a new front panel. Get out of your Bitx rut!  We dared to do something different, and this follows with the soda bread. 

On my daily shifts at the Board and Care facility the XYL has been watching the British Baking show series. Talk about watching a show over and over and thinking it is a new show each time. One of the baking challenges was Soda Bread. That caught my interest.

It seems like with many things, the history is clouded with credit for the Soda Bread recipe cited as Native American but popularized by the Irish during the potato famine. Like the J310's (see there is a link) the ingredients are sparse. 

With four ingredients: flour, baking soda, salt and buttermilk you are there. The other delight was 35 minutes from start to finish. No rising of yeast is required or needed! 

The dry ingredients are first combined and then the buttermilk added to form a dough. The dough SHOULD NOT be over handled as that makes the bread tough. A simple mixing using a butter knife in a large bowl and a final formation into a 6 inch in diameter by 1- and 1/2-inch Pattie is placed in a pan. The Oven should be pre-heated to 450F, and the bread cooked at this temperature for 10 minutes. The temperature is then reduced to 400F and baked for 20 additional minutes. All-important an X shape is cut in the top of the bread dough before baking. The resulting bread structure is thick, and several pieces toasted along with a platter of eggs was a breakfast delight this morning.

Two cups of all-purpose flour. 1/4 teaspoon each of baking soda and salt and 1 cup of buttermilk --- that is it.



You must remain awake during a blog reading as you may miss the connective points -- Soda Bread is indeed related to J310's ~ Simple and Sparse but Oh so Good!

73's
Pete N6QW


Saturday, April 20, 2024

April 20, 2024. The Ubiqutous Mic Amp and Balanced Modulator

 Following our template of small circuits and easily digested (almost) presented forthwith is a circuit module for a Microphone Amplifier and Balanced Modulator. 

This will terribly disappoint those home brewers who must see all and every component in a build and whose tenet is everything is scratch built. We used a packaged Double Balanced Mixer (SBL-1) and a Low Noise Op-Amp NE5534.

This circuit board is out of a project by me published in QRP Quarterly entitled JABOM (2011). Oh, you ask, JABOM is an acronym for Just A Bunch Of Modules. Of note the use of single sided copper vector board versus the Manhattan glue down, as the construction medium.




 
Later a Copper Box made from Double Sided PC Board was built and soldered to this board. The box had feed through caps and RCA Connectors. This added to the shielding of various circuits and made this "bullet proof". 
 
The 50K Trim Pot sets the Microphone Gain Level. But for those who are anal retentive there was also a panel mounted gain control that enabled mic gain level adjustment.
 
Now, full disclosure you could build this circuit with a homebrew DBM and use a single 2N3904 as the microphone amp. But one of the key advantages of this topology is lost if you use an ADE-1 an ADE-6 or a TUF-1 or TUF-3.

 



 

 


So, you ask what is so special about this circuit module. The answer is two components: the 100 Ohm Trim Pot and the 22 Ohm resistor. While the SBL-1 is a Double Balanced Mixer, these two components make it possible to UNBALANCE the Balanced Mixer. Why? The answer is to provide a "Tune Up" signal. This obviates the need to shout HOLA into the Microphone!
 
With the 22 Ohm Resistor un-grounded the 100 Ohm Trim Pot is balanced so no Carrier is present. The small relay when engaged, grounds the 22 Ohm resistor which unbalances the SBL-1, and the carrier is passed on through the circuitry. The microphone is not keyed as the signal to trip the relay also trips the PTT.
 
I did contact Mini-Circuits about the feasibility of doing this and while they thought I was nuts did say it would work. This bit of a tip now is forever ensconced in EMRFD. 
 
Hopefully this added to your dining and dancing pleasure for today.
 
 

 
73's
Pete N6QW

Friday, April 19, 2024

April 19, 2024. An Audio Amplifier you can Build.

I find that data is very useful in making decisions. How startling a statement to make on a ham radio blog.  For instance, when I post subjects about how to build some small building blocks for a radio project that gets more views than something like fabricating a complete rig or a linear amplifier like yesterday. So back to the building blocks.

But 1st the elephant in the room. I am less of a purist than other homebrew hams. I tend to look at the utility provided by circuits and not so much as the pedigree of the topology. I am OK if I cannot physically see every component in a build (discrete parts versus IC's). My rational is performance, cost and time to build.

Many an argument has been made about building audio amplifiers using totally discrete components versus adding in IC's. I usually will test drive a particular topology and then decide what fits best with the desired result and my time available.

Yes, I have built discrete audio amplifiers, and a good example was The Let Build Something Project   I was able to improve this design by adding in place of the 2N3904 and 2N3906 the TIP31C and TIP32C devices for more output with no other circuit changes. 

Thus, today an audio amplifier stage using not one, but two IC's is presented for your dining and dancing pleasure. The pre-amp stage uses the NE5534 which is a low noise op-amp, and the output IC is the 14Pin LM-380. This can be built using Manhattan construction and I would suggest the use of W1REX MePads as that will put you on a better path to success. For me I have this design in my CNC computer, so I just punch the start button.
 
 


You will see this amp in many of my projects including the KWM-4, The Sudden Transceiver and The Simpleceiver. 
 
So hopefully more views than a tube linear amplifier using high voltage.
 
BTW the Lets Build Something link (earlier in this post)  if you look an the 2nd Generation LBS link there is another audio amp with a 2N3904 driving the LM386-3 IC
 
73's
Pete N6QW



Thursday, April 18, 2024

April 18, 2024. Linear Amplifiers for your QRP Radio

The following subject is on par to bringing with you an ice chest of Cold Beer to a Tent Revival Meeting on a hot July Sunday afternoon. [It is with uncertainty that you would be marched out of the tent or mobbed to get a cold brew.]


Linear Amp with Tubes.

 

Yes, this AI stuff works as this showed up on my Android phone and I do not know how it did.


One of the early on paragraphs states this is a linear amp for QRP Transceivers so there is a connection to this blog. 

I just had a revelation that QRP follows QRO in an alphabetical listing -- so who ever came up with the Q Signals was a visionary that you must step down for less fire in the wire.

I have many QRP homebrew transceivers, and you can spot them on my You Tube channel, so they do exist. Literally all of them include the ability to switch in an external linear amp. My current 40M homebrew SDR Radio can operate at 5 watts, 120 watts or 600+ watts. That is a lot of fire in the wire. 

I must admit that I had to add a whole bag of snap on Ferrite cores to clean up the RF feedback when operating at nearly 700 watts out with a rebuilt SB-200. But the norm today seems to be 100 watts and a wire at home and QRP from a SOTA site. 

Now we will have those who read this blog yelling that they bought a 100-watt solid state amp kit from China for $17.87 plus $2.98 speed-pack shipping. So that is an alternative.  I have seen those kits but am uncertain as to their outcome.

The amp in the link is good for 150 watts and is homebrew. There is a terrible negative to a tube amp and that is the high voltage. Most hams who are less that 65 years old (born after 1959) have never worked with HV so that is a real serious concern. 

But for the most part this amp puts out 150 watts and that is a great power level if you want something more that beating your head against the wall trying to make contacts running 5 watts with a dipole up 10 feet in the air at sea level. 

So, this is presented today because some AI software found me and now, I share this with you. One of the better Solid State Amp suppliers is in Ohio and that is Communications Concepts Inc. They have some interesting kits and two of my amps were supplied by this company. One kit offering does 300 watts with a 28 VDC supply and has low drive requirements. Figure about a dollar a watt will give you plenty of fire in the wire using this kit. 

There is another key element in the link and that is the actual build construction done by non-US hams. Homebrewing from afar seems more prevalent than from those who simply flash the plastic at Amazon and are not forced to be creative in using what they have.

73's
Pete N6QW

Wednesday, April 17, 2024

April 17, 2024. Something you can build.

 


Check N2CQR's Solder Smoke Daily News posting yesterday for a really super neat Direct Conversion Receiver project (DCR) from Geoff, N6GWB. One of the circuits he mentions he used with the J310's configured as a Dual Gate MOSFET is based on this design from me. Not a lot of parts but surely a lot of performance.

For the full detail of the J310 DCR check my N6QW website. The direct conversion receiver offers a superb result for not a lot of hardware nor lot of money. Yes, something for those who had to pay Uncle Sam some $$$ a few days ago.

Notably this same circuit topology was used as an IF amp stage by substituting a fixed Bias on Gate #2. I found a module using this approach in the Junk Box and have a "sorta of working" SSB Transceiver using that old module. You will see that shortly. Yes, it has a homebrew 4.9152 MHz four pole filter and for those with a Nano VNA you could actually use that jewel on that board.

I mentioned to Geoff, that a companion project would be a matching transmitter. Yep, I am planting seeds for a PNP transmitter to be built. 

Always slightly ahead of the curve. Noteworthy and sounding like a broken record, LT Spice is used to tweak the circuit before you buy any parts or turn on the Soldering iron. There is a note there about the use of the 2N3819 in place of the J310. Not as good but if you have some in the junk box -- no excuses not to build a DCR.

73's
Pete N6QW

In case you are keeping score...

 Interesting results... Iowa : Joni Ernst's Republican seat was won by Democrat Josh Turek. [senatordb.com] , [ballotpedia.org] Kansas :...