Wednesday, March 20, 2024

March 20, 2024. The Equivalent of a Swiss Army Knife!

 

A Swiss Army Knife in Disguise!

 

 


This post today is in special recognition of the segment of the blog readers who are averse to things like the Arduino MCU and programming them. This specific circuit we soon will discuss could easily be done today with an Arduino Pro-Mini or Nano. But in 2009 when this was 1st started the MCU's were not as prolific as they are today. This circuit will have appeal for those that have a non-Arduino comfort zone.

Perhaps with the exception of the P3ST 20M SSB Transceiver, where I purposely set out to not build a warmed over Bitx, EMRFD rooted or TIA based rig, often what I design is in response to a specific problem or issue. The above circuit is exactly that scenario. Soon you will also see its connection to the Swiss Army Knife.

If you check my Tri-band Transceiver found at 
https://www.jessystems.com this was the starting point. That particular rig has many circuit modules and power is switched to these circuits in Receive and then to Transmit. The switching was substantial and needed a rather large relay. Yes, relay spiking that even with a snubber caused a frequency shift in the PTO (from a Ten Tec Triton IV). 

To respond to that issue, I designed an equivalent of a Solid-State relay which is the upper half of the schematic. The Opto-isolator was just a way of debouncing an "ON" signal to the 7400 wired as two inverters. Pins 1,2 and 3 is one inverter and 4,5 and 6 the other. 

The 10K pull up resistor with the PTT disengaged provides +5 to Pins 1 and 2 which means Pin 3 is inverted to "0" and Pin 3 now causes an inversion on pins 4 and 5 which means Pin 6 is 5 volts firing the 2N3904 and we have +12VDC for the Receive circuits. 

When you hit the PTT the 10K Pull Up is set low through the 4N35 and that toggles the 7400 so that Pin 3 is now 5 Volts turning on the Transmit 12 VDC and Pin 6 is low turning off the +12VDC to the receive circuits. 

[There will be a bunch of blog readers who say PFET's and why all that old stuff. Hey, I had all of the parts in the junk box, and this is a solid design. That solved the issue we saw with the relays.]

Fast Forward to 2012 when I built the KWM-4 and again lots of circuit modules and the need for extensive voltage switching. But on purpose the KWM-4 was to be both an SSB and CW transceiver. The addition of CW created the need to have some effective way of creating CW while switching in the CW only circuits. We also needed a way to Tune the Transmitter with a control on the front panel.

Those with a keen eye will see that the lower half of the schematic is an independent circuit which essentially is keying an NE555 timer IC and the input comes from the CW Key or the panel mounted Tune Switch. The outputs include a keyed voltage to key a Buffer Transistor, a circuit to trip the PTT via a small relay and voltage outputs to various parts of the circuit that are only used for CW. One of those is a CW oscillator at 455 kHz, used only on transmit. BTW the 4.7Ufd cap sets the timing for how long the timed voltage stays on. Those who do 25wpm CW likely will want a smaller value of hold time.

The 1st 455 kHz IF amp stage (bilateral) in normal operation is connected to the Collins Mechanical Filter via a relay that is only activated on CW, removing the connection to the Mechanical Filter. The NE555 produces a timed output voltage and one connection to that Pin is the relay. When that relay is energized it is sending the signal to the stage in the reverse direction. Thus, the output from the keyed Buffer stage is fed to this relay and on out to the Transmit circuits. On CW the mechanical filter is not used in transmit.

This solves a problem with the KWM-2 that uses an audio tone dumped into the Balanced Modulator. To meet FCC requitements that tone is 1350Hz which is useless today for CW.

Along the way our control board also provides a relay closure to control an external linear amp.

Hopefully as you understand what this control circuit does that you will identify its Swiss Army Knife comparison.

Lucky me the design is a CNC program and if I want another Board, I just punch the start button.

73's
Pete N6QW


Tuesday, March 19, 2024

March 19, 2024. A Digital Interface for your Radio.

Something for our Software and Digital Followers. We must expand the tent to be All Inclusive!

A Digital Interface

 


So, OK, you are an entrenched homebrew, Analog VFO, CW QRP, minimalist enthusiast and here is this guy wearing a beret from Southern California trying to lead you to the digital dark side.

Yes, that is exactly what I am doing but maybe only to share some of my experiences and information with you. Disclaimer: upfront you must have an SSB rig tuned to USB to have this work on the several digital modes that are mentioned.


I have been at this hobby a long time and aside from doing the WSPR thing several years ago with my Softrock V6.3, I am not deeply involved with digital operations. But seeing as I have a few SSB rigs available for experimentation coupled with some new digital modes I felt it time to once again test the waters.

Coincidentally a program from K1JT, Joe Taylor, called WSJT-X has many of the digital aspects rolled into a single program which are simply menu selected. You must download this free program to the computer you will use.


Two of the currently popular digital modes are WSPR (Weak Signal Propagation Reporting) and FT8. WSPR has been around a long time and essentially has you tune a specific frequency and listen for other stations. Periodically your transmitter, under computer control, is turned on and other stations listen for you. Most often stations run QRP power levels like 30 dBm signals (1 watt), some even less. I have been spotted 10,000 miles away running 500 MW (27dBm or 3dBm down).


The key feature to this program is the real time database where you can see who you have spotted and who spotted you. Today 40 Meters is a DX band and spots spanning great distances is often the common experience. WSPR uses a two-minute time block and so you can watch your lawn grow during the two-minute intervals. The 40 Meter WSPR frequency in 7.038600 MHz USB. Included on the WSPRNET webpage is a world map which captures the spots specific to your station. I learned a lot about my antenna as the spots are consistent NE SW


FT8 is a recent addition to the digital array and this format is much quicker as each pass is 15 seconds and is more QSO like.  A station sends a CQ call, and the computer screen shows the station who sent it. Boom, double click on that call and the computer takes over by responding and then listening for a return. The computer will continue doing this until the person responds back OR another station picks him up. Once the connection is made the computers on each end exchange signal reports, confirm the reports and send 73’s. 

It is indeed a craze; but some naysayers have likened it to remote quickie sex, you were present and that was about the extent of it. A variant called FT8CALL now adds to the sequence by letting the operator add text and other information, so it is more like a QSO. The FT8 frequency is 7.074 MHz USB.

When I was using the Softrock V6.3 much of the interconnect to the rig and the computer program was done entirely in software within the computer. With a standalone rig, this requires some hardware to do the interconnect. A little time with the Internet resulted in a configuration that will do that task. Pre-made inexpensive circuit boards are readily available; but also, there had to be some adjustments made to work with modern computers.


The first board is a sound card interface kit from KF5INZ that was available on eBay for around $7 USD. This board has a couple of 600:600 Ohm modem transformers and some keying circuits that trigger and opto-isolator switch from either a DTR or RTS signal via computer Serial Port. That is the first issue as most modern computers don’t have a Serial port as everything has shifted to USB. 

 

That was one of the first nuts to crack. Although initially I did use the Serial port on an old Windows XP Pro computer; but then later shifted to the USB. Knowing what I know today I would not buy the kit, but just build the modem isolation part. Essentially, I have abandoned the Serial Port keying. [In the WSJT-X setup for the rig pick NONE for a homebrew radio, and for the keying use RTS. There is a setup page where you make these selections.]

 

I also have abandoned the XP Pro machine and now the system is running on a small form factor Windows 10 NUC computer that is about the size of a CD case and 1 inch high. This computer has only an earphone output, so I added a plugin USB Sound card Dongle from Sabrent (about $7) as that provides the audio in/out capability. For the triggering of the PTT, Adafruit Industries makes a small USB to Serial board that is quite small (CP2140). One of the outputs is RTS – perfect. But the output logic is only 3.3 volts whereas the Serial Port is 10 Volts. So, I needed a way to trigger the PTT from 3.3 Volts. A simple 2N3904 transistor switch, a SPDT relay, isolating diode and one small resistor handles that chore. 

 

The WSJT-X has a settings tab that requires you to enter your call sign, grid square and the method of keying (RTS) and the COM Port to be used. There are some other items that require checking the block, like double click to automatically respond to a CQ and to disengage the transmitter once your computer sends 73’s. Spend a little time with this setup and look at all of the tabs. I didn’t and then wondered why nothing worked. One problem was my computer clock lost track of the time.

 

Oh, a cool feature of the WSJT-X –it is linked with hamlib. When you call a station, it tells you the azimuth (like if you have a beam) and the distance from you. Pretty cool but this is only used with specific radios. For a homebrew radio use NONE


I am happy to report that my interface box has been in operation for several years and works for me.


Below is a page from the WSPR database. I was running 5 watts (37 dBm) with a droopy dipole. Imagine being heard 12000 km away with that kind of lash up. But that is a significant bonus to digital operations, especially FT8, as it levels the playing fields running low power and modest antennas. So that may be a real appeal to those with QRP rigs who have antenna restrictions or live in apartments.


 

 

 

 

This is the modification to the Adafruit CP2140 to key the PTT on the transceiver

 

 

 

Below is a pictorial of the component/board interconnects.

 

 


Finally, this is the schematic of the Sound Card Interface board. Based on my current experience I would just build the modem interface which is two transformers, two resistors and two capacitors. A friend in the UK was going to purchase the board from the US and the shipping cost was $20 for a $7 board. So, skip the Serial Port Interconnect and go with the USB.


 

A couple of cautions. Upon initial setup with the Adafruit board connected to your computer using the control panel, find the COM port associated with the USB as you will need that to enter information into the settings page. The next caution involves the computer, which by the way had me baffled for about an hour or two. I could see the signals on the waterfall; but they were not being registered on the panel and neither was anyone copying me when I transmitted. Like a ton of bricks, it hit me. My automatic update of the computer clock was not updating automatically. A synchronization with Internet Time and all was good.


Unlike other programs and since my rigs are homebrew, I must physically tune the rig to the WSPR or FT8 frequencies. With other software auto tuning of the rigs to the frequencies is done automatically. Appliance operators would consider this an inconvenience but as a homebrew guy it is just another day in the shack.


I should note that you will need a super stable VFO to work the digital modes. My homebrew rigs  all use the Si5351 PLL or AD9850 DDS. It may be possible to use an analog VFO but unless it is using a X Lock 3 frequency stabilizer (G4GXO but no longer available) your results may be marginal. I was able to do FT-8 with my KWM-1 which uses a PTO and after warming up is stable enough for FT-8


I will be looking for your signals on WSPR or FT8.

 

 73's
Pete N6QW

In case you are keeping score...

 Interesting results... Iowa : Joni Ernst's Republican seat was won by Democrat Josh Turek. [senatordb.com] , [ballotpedia.org] Kansas :...