Monday, June 9, 2025

Reading the Tea Leaves.

Reading the tea leaves which in a broad sense is observing the data and making a determined decision is so important. It took a while before discerning FBF (Feed Before Fun) was required with Mary Jo. 

I wired up a power plug (hay wired is more like it) and did a bit of initial sleuthing with the HW-32A straight away from the storage location. The tubes light and I can hear a signal generator about 5 feet away but not physically connected. The signal is detected at maybe S5 but not like other radios (commercial and homebrew) where the S meter is pinned using the same approach. 

I actually heard two stations but for the most part the receiver was deaf. This is a tea leaf moment, as the receiver system is not amplifying the signals from the antenna to the speaker. Don't rush over that point too quickly.

For many blog readers this is a BOB (Bordering On Boring)  moment especially since we are dealing with Thermatron's. If you feel BOB'd you missed the memo. The real thrust at this point is a trouble shooting methodology which applies to any receiver whether tubes or the latest SDR.

Another critical piece of data from this initial test is that the receiver will actually do all of the steps in the block diagram --- but in one or several places not too well. 

It seems like a functionality included in most transceivers of this vintage was the capability to use the transceivers with an outboard receiver. Check your old Drakes and even early Ten Tec's. The HW-32A as well has the capability. In the HW-32A scheme the antenna relay takes the signal at the antenna and routes it through a set of relay contacts and then on to a separate winding on L3 that has the main winding in the plate circuit of the 12BY7A Driver tube. 




The connection point for the external receiver is AFTER the relay contact. So, if you connected an antenna at that RCA jack versus the external receiver you would be applying the antenna directly to the winding on L3. This is a test. Suppose the antenna relay contacts are bad then you would get little signal into the winding. But the test showed the same signal level with the antenna properly connected to the Coax connector or to the external receiver port. Scratch the Relay off the list as the issue.

Another noted anomaly and perhaps a 1st area to fully evaluate. At Power ON the S Meter pins and as the tubes warm up the S Meer drifts down to less than S1 as the atmospheric noise drives the low-level S Meter reading. 

I see the same action with my Collins KWM-2. So that is a normal response. Now as you advance the VOLUME control the signal gets louder but then you hit a point where the background sound is loud, but the signal disappears, and the S Meter gets pinned like at Turn ON. Let's look at that portion of the schematic (Think AGC).



 



A 6EB8 is used as the Audio Pre-amp and Audio Amp stage. Pin 3 on the Triode section connects to the top end of the Volume control through a capacitor, a 5000pF (.005 Ufd). Also, off Pin 3 is a 220K Resistor in series with a 0.02 Ufd (20,000pF) Cap feeding the AGC circuit (the two diodes). The Caps and Resistors in the AGC circuitry set the attack time and decay times. The output of the AGC circuit goes to only one place --- The Receiver RF Amp Tube direct into the Grid of V8A, Pin 2.

Let's digest that for a moment. If we have an extremely strong signal that passes through the receiver system when it hits the triode section of the 6EB8 that signal (an AC type signal) it is rectified by the AGC to produce a NEGATIVE voltage whose level is proportional to the input. That negative voltage goes into V8A Pin 2 and reduces the RF amp stage gain. 

Under normal circumstances this works pretty well. But the low recovered signal levels and the pinning of the S Meter when you full open the Volume control signals that the AGC is very much reducing the RF stage gain at low signals levels which it shouldn't to completely cutting off the RF amp tube and pinning the S Meter.

Well at least that is a starting place to wit if the 5000pF cap at Pin 3 to the volume control is shorted that certainly would impact what happens to the other components connected to Pin 3. The immediate argument contra to a shorted cap would be that DC is being pumped into Pin 7. But look closely as there is a 0.02Ufd cap off of the center wiper on the Volume control that would block the DC and the audio amp would still work.

This is the last posting on the HW-32A as we have hit the #3 gag level, and most blog readers are yawning at this point. But if you look deeply into the blog posting it is not about vacuum tubes but a trouble shooting process. 

A brute force action on my part is to replace many of the components on the 6EB8 circuitry including the AGC part. This may not fully resolve the problem but certainly we can then scratch that off the list as possible issues just like the antenna relay.

I am hooked (more like an obsession now) on proceeding with the HW32A re-invention and so future blog postings will be more than a little light as I spend time on the rejuvenation.

Them that know can make things go.

Pope Leo for POTUS 48! Wow that would certainly rancor the separation of Church and State advocates. Just like letting the lions loose in the Colosseum, a real spectator sport.

73's
Pete N6QW

Sunday, June 8, 2025

Demystifying the HW-32A ~ Or why it shoots craps!

A Partial Block Diagram of the HW-32A

 









The why it doesn't work boils down to a simple two corks in the bottle L2 and L3 and associated circuitry. These two Inductors (transformers) are in both the Receive and Transmit Paths. If there is something awry in either one or both of these circuits, then you will have issues in Transmit and Receive. The faint received signals and low output are the symptoms. BTW V5 and V8A both test good so not a tube issue per se. In fact, a retest of all tubes shows all are hot!

These two inductors are in closed shielded cans and only accessible through a bottom hole. Once set they are intended to be forgotten. This suggests broad band by design. Previously I removed both inductors from the chassis and opened up the cans. In L3 there was a strange bit of an add on. The cans are closed for a reason -- they are critical to the proper operation and Heathkit was trying to protect us from the accidental use of the Golden Screwdriver.

At the top of the inductor core inside the shielded can was a small glass bead and I think its purpose was to prevent the adjustable core from transiting outside the coil form and to anchor the core in the can. Yes, it popped out never to be found. 

Long ago I bought a bargain HW-18 Civil Air Patrol two channel SSB transceiver. It is a similar design as the HW-32A and has an L2 and L3 intact. However, this L3 Coil has an open top and the cores can be adjusted from the top. So, I have a fall back to adapt the HW-18 L3 to the HW-32A should that be necessary. 

DO NOT TRUST YOUR MEMORY... IT WILL LIE TO YOU AND MINE DID!

Here I have been going on about the 4 Pole Crystal Filter being 3395 kHz. It's Not. The Nominal Center Frequency is 2305 kHz. I spotted that when I was creating a large schematic from several PDF page found on the Internet. The Carrier Frequencies are 2303.3 kHz and 2306.7 kHz as noted on the drawing. So, we will need to amend our calculations and the sketch. RTFM applies very well here.

Next is a schematic of the heterodyne VFO portion of the HW-32A. Essentially a VFO operating between 1618.300 kHz and 1968.300 kHz (near the AM broadcast band) when down mixed with an 18.275 MHz signal yields a LO range of 16.656700 to 16.306700 MHz. Now subtract 2306.7 (USB VFO) and we get 14.000MHz to 14.350MHz. Perfect and this will work with the JF3HZB Analog Dial sketch.





Where the Plate of the 6BE6 connects with L5 we will need a small value but high voltage ceramic cap and this becomes the injection point of CLK0. V13 and V14 are simply removed and their filament source voltage for these two tubes can be fed to a DC rectifier and three terminal regulator which will then be the source power for the ESP32 and Si5351.

This is not a one and done project but will take more than one month--maybe three. Fixing the stock HW-32A remains Job#1 and once there we can add the digital LO and the JF3HZB dial.

Them that know can make it go.

Holy Moly! Just saw where Pope Leo has an event that is sold out the same day as you know who's birthday. Scary thought: Does Pope Leo meet the qualifications to be POTUS 48? Hmm you can tick those off but certainly in the zone. He is already a Head of State, US Born and over 35 and well connected here on earth and beyond. [This is an endless rabbit hole.]

73's
Pete N6QW

Saturday, June 7, 2025

An attempt at an upgrade of a Heathkit HW-32A SSB Transceiver.

 




For the past couple of months, I was seeking a donor HW Monobander. But in truth, I actually had one in a storage area. We all know the huge issue of finding something in storage. Well, after several months of plaintive pleas for a donor radio, I was left empty handed. Thus, a sojourn to the storage area to retrieve the HW-32A. Yes, I had to go through all of the boxes, and it was the very last one.

Physically it is OK, but it has a significant circuit issue that after chasing it for some time I gave up. Thusly banishment to the storage area. So now I have to fix it. Yesterday I wrote the code for the ST7735 display and that is done. (More on this.)

The plan is to get the HW-32A working as designed and then the treatment with the JF3HZB dial.

I have done a fit check of several sizes of displays, but that semicircular hole is an odd duck. The panel space is 12X6 inches and I have a chunk of aluminum that exact size. 

A potential possibility is to create a whole new front panel and cut a rectangular hole in the new panel for a Color TFT display. This approach would enable the use of a large ILI9341 display. The original panel would now be a template for cutting most of the holes in the new panel. A Juliano Blue or Canary Yellow color front panel would assure a notice.

But wait! This is a complex project because of what Heathkit did! That blog readers is the challenge. At times I just do things because I can but often because it is a real technical challenge. The Circular Analog Dial with the HW-32A is a Technical Challenge. Part of that challenge was highlighted in the past postings dealing with the 40M Channelized radio that was fitted with the same Heathkit crystal filter frequency.

Today, especially with the advent of Digital LO's and BFO's the single conversion topology is the circuit of choice. The real ham technical experts (the non faux wannabe's) will give full throated testimony to the soundness of the single conversion.

But the HW-32A is a Single Conversion Design and that is the challenge in the required engineering evaluation to make that work. Let's take a shallow dive into the issue. The Heathkit 4 Pole Filter is at 3.395MHz and the heterodyne frequency is at 18.275 MHz (simple Crystal Oscillator) and is added/subtracted to the VFO frequency to form the LO. 

Shazam, Heathkit used a VFO operating in the range of the broadcast band. In fact, I think that is one of the operational checks to see if the VFO is working -- listen for it on your AM radio. This low VFO range when mixed with the fixed heterodyne signal made for a far more stable radio than a VFO operating at 10+ MHz. 

Now I earlier said I got the JF3HZB code working for the HW-32A. Well, that was only to see how it would look on various displays and how the front panel will look with the various sizes. It is not the final design!

So here is an array of technical challenges. Throw it all away, keep some or only use the JF3HZB as the VFO. Each of these involves a significant modification to the radio and the sketch. The change the VFO only option involves a bit of code trickery because of the heterodyne VFO conversion.

Let me explain the last option. You want the display to show as in the second photo. But the original JF3HZB code is based on single conversion with a subtraction of the 3.395MHz IF. This has to be accounted for in the code and since we have a subtraction it will be a sideband inversion and the frequency actually subtracted is not 3.395 but 3.396500 MHz, the USB BFO so that the dial reading is accurate.

Heathkit did make it somewhat easy as the VFO and Heterodyne Oscillator (V13 and V14) have their filaments series connected. Simply pulling those tubes out of their sockets is all that is needed to null those functions. A new LO from CLK0 can be introduced into L5 and that solves the problem of a single conversion.

Still another waypoint decision, the BFO. The HW-32A has selectable sidebands and so do we keep that function or disconnect the crystals and simply feed CLK2 into the grid of the Carrier Oscillator. The former USB/LSB select switch could now be an input to the ESP32 to provide the proper Carrier Frequency. Is there a possibility of generating a USB Carrier and the other a CW carrier on transmit and use the HW-32A on CW? More complexities

So, the real thrust is to get the HW-32A working as stock. My past foray on getting it proper was L2 and L3 as the signals (both on transmit and receive) were in serious need of a shot of Viagra. 

L3, which is in the plate circuit of the 12BY7 Driver Tube has a link coupled winding from the antenna relay and thus is also in the receive path. A limp signal on Rx and Tx would sure point to that area of the circuitry. Faint signals and but a few watts on transmit are the symptoms.

This could be a serious overall technical challenge and another adventure at the N6QW Laboratories.

Them that know can make things go!

73's
Pete N6QW


Friday, June 6, 2025

A Mate for the ARC-5 Receiver ~ A blast (of RF) from the past!

 








A bit of propagation sure helps, and two things are evident: An ARC-5 sounds better on CW and the band spread is awful. Just imagine relying on this radio as if your life depends on it.

The transmitter shown above uses a 6L6 built using a bread board, more or less on a whim, but does show this could have been OK for a station rig. At 12 watts output it would certainly be the bottom level for consistent reliable operating as a main rig. I always suspected that the design would support perhaps as much as 20 to 25 watts output. 

The shortfall I reason likely lies in the low plate voltage at 300 VDC and a non-optimized output network. The Variable cap in the upper right-hand corner of the bread board was an attempt to provide additional "Loading" in the output network. 

Featuring front panel selection of "rocks" the FT-243 crystals sound much better than the plated HC6-U type. There are three frequencies 7.010, 7.028 and 7.o58 in the rig. These were found in the junk box but certainly ideal for operation today. Not quite a Si5351 but a bit of QSY wiggle room.

Plug In Tank Coils facilitates operation on 20 Meters using two of the crystals doubling their frequency to 14,020 and 14.056 MHz which are OK for 20M. Thus, part of the tank circuit on a plug-in coil form.

We have reached the reader gag level so time to move on with more exciting adventures from N6QW's junk pile.

Them that know can make things go.

73's
Pete N6QW







Thursday, June 5, 2025

Have you ever used an ARC-5 Receiver?

For a majority of the current US Ham population, to that question we likely would hear a resounding NO. Most wouldn't even know what it is.



A 3 to 6 MHz ARC-5, BC-454


My 40M ARC-5

Way before the US formally entered WWII there was a push to modernize our military communications hardware. The ARC-5 components were actually a system of small sized radios that covered a portion of the LF and HF bands (up to 9 MHz). Obviously, the intended use was in aircraft.

At this time the physical size of the ARC-5 radio sets were small in comparison to a SX-28 or HRO-5. The receiver portion of the system used 6 tubes and depending on the band used different IF frequencies. The BC-453 covered the LF band and had an IF of 85 kHz. The BC455 (6 to 9 MHz) had a higher IF in the MHz range. 

The Transmitters were a bit physically bigger and had 4 tubes including a magic eye tube. The output stage used a pair of 1625's (12V version of the 807's) good for 100 watts on CW.

ARC-5 Transmitter




Two seconds of thought should make clear that by choosing the variable IF a very stable LO could be built in a single conversion approach. The Receivers could receive AM and had a BFO for CW. The transmitters could do CW "as is" but there was an accessory Modulator Box (BC-696) needed for AM.

In normal operation in an Aircraft the ARC-5's operated from 28VDC using a strap on Dynamotor for the Plate and Screen voltage and the filaments were wired series parallel to operate from 28VDC -- aircraft power.

Post WWII the Receivers and Transmitters were highly prized by the ham community. In 1955, ten years after WWII, I bought a NIB BC-454 (3-6MHz covering 75/80M) for $3.50, and a purpose-built power supply (plug in for the Dynamotor) was another $7.50. So, for $11 I had a ham band receiver.

The units were built like a battleship with gear drives on the VFO's/LO's. The build included gluing down all VFO wiring using "Glyptal" so the was no component movement which would affect frequency. Surprisingly the dials were linear and repeatable!

[Glyptal has been used in ARC-5 radios primarily as an insulating and protective coating. It helps seal and protect electrical components from moisture, corrosion, and vibration, which is crucial for maintaining the reliability of these vintage military radios. Some enthusiasts and restorers use Glyptal to recoat transformers, coils, and chassis interiors to preserve their integrity and prevent electrical shorts. Courtesy of Microsoft copilot AI.]

The BC-453 (the LF variant) tuned at 455 kHz, suddenly became a very hot item. It was known as the Q5'er.  The trick was to take an output from the IF of a commercial receiver at 455 kHz and feed that into the antenna of the BC-453. You now had a dual conversion receiver with a second IF at 85kHz and a very narrow bandwidth (Q5). A really enterprising conversion by two California hams made the BC-453 into a SSB Transceiver



A discussion of the ARC-5 system would not be complete without a mention of Tony Vitale, W2EWL who converted an ARC-5 Transmitter into a Phasing Transmitter in a seminal QST article entitled "Cheap and Easy SSB'. In the early days of SSB, Tony's rig was found in many Mobile SSB installations. Read about it here on N2CQR's blog.

My very 1st station was the BC-454 and a 6V6 built on a wooden chassis at 3709 kHz (then a valid Novice CW operating frequency). For a TR I used an "open" big old DPDT knife switch. More than once I got RF burns a result of touching the switch while I was still transmitting.

When I headed off to Penn State in 1959, my BC-454 was on the bookshelf along with the textbooks. It was a great way to keep a connection with hobby while I was away at school.

Et Al, the ARC-5 was a pretty rudimentary system and consider that they were mass produced, and their life expectancy was in terms of months not years. So not much in the way of frills. 

For long haul communications in the Bombers, we would see the BC-348 or HRO for the receiver and of course the Collins ART-13 with autotune for the transmitter.

I have always had weird ideas about commercial or military radios. The 1625 transmitting tubes used in the ARC-5 were really cheap like 25 cents for a NIB and so there was much interest in building transmitters using these tubes. 

One issue with the 1625 was that the Cathode was internally connected to one of the grids. Hams being hams simply sawed into the base of the tube and removed that connection. You ask why? The answer is SSB operation using the Cathode Driven (grounded grid) topology which wanted to see only the Cathode. A pair of 1625 suddenly was a 100-watt Linear Amp. 

I went one step further and converted an ARC-5 Transmitter into a complete linear amp including building the power supply inside the case.

At the time I had a Yaesu FT-7 which is a QRP radio and with the ARC-5 Linear it was now an all band 100-watt Transceiver. When I sold the FT-7, the amp went with it. What a hoot.

So now you know a bit more about the ARC-5 radio system. Don't bother to look on eBay -- a decent ARC-5 is upwards of $200, and I paid $3.50 in 1955.

Finally, many conversions of the ARC-5 receivers involved rewiring the filaments for 12VAC. Actually, if you were the clever sort, you could have a twofer. If you purchased two 25.2 VAC Filament transformers one at 3 amps and another at 1 amp you had the makings of a complete power supply for the ARC-5. 

Step one made the 3-amp version as the side connected to the mains. Off the secondary you would light the filaments as well as provide an input to the second 25.2 volt trans former. Essentially the secondary sides were connected back-to-back. 

So now what was the primary on the 2nd transformer was now the secondary. That voltage was fed into a bridge rectifier and instantly about 160VDC for the plates and screens. Thus, a twofer with two transformers connected back-to-back.

Them that know can make it go.

73's
Pete N6QW

Wednesday, June 4, 2025

Acorn Tubes. QRP with tubes that are only a bit bigger than fat Transistors

 














Acorn Tubes are really small tubes that were designed during WWII for use at UHF frequencies. I got my 1st Acorn Tube when I bought a WWII surplus Radiosonde Transmitter. 


Needless to say, long ago, when hams would build things and not just do contests, POTA/SOTA or plain operate, these Acorn tubes found their way into homebrew QRP CW transmitters. Several years ago, I even saw a radio set using an Acorn Tube CW Transmitter complete with a matching Regen Acorn Tube Receiver. What a hoot.



Rex Harper, W1REX, during the virtual 2020 FDIM Buildathon (you know that COVID 19 Crap) used this schematic as the project foundation. I think it got close to a watt output with this lash up.

I didn't participate in that event but did build my version using scrap stuff I had lying around the garage. The tube filaments are wired in series so I could simply supply 12 VDC through a three-terminal regulator. 




Since Cycle 25 has been sub-par (a highly touted but major disappointment) and given the MUF yesterday was no higher than 30M then this jewel would be FB on 40M.

Before anyone gets their underwear in a knot about high voltage DC and the need for a special power supply... Think 20 Transistor Radio Batteries in series. The current draw is less than 10Ma so as they say in Italy -- Non รจ un grosso problema.

Or in plain English -- "Ain't no big deal". I checked Amazon and twenty 9VDC batteries cost less than $15.

An overwhelming resource on simple vacuum tube receivers can be found here thanks to K3UH. You could get lost on his site for weeks at a time.

Band conditions are supposed to be better today so maybe we can test the ZIA. The MUF is better but unsure about the other one.

Them that know can make things go.

73's
Pete N6QW


Tuesday, June 3, 2025

Looking for a Heathkit Monoband Transceiver.

Since Cycle 25 sucks, I thought I would get serious about revamping one of the Hot Water rigs. Please check your storage lockers, in the attic space or under the workbench. It doesn't have to be working just all there.

[Checked the MUF (Maximum Usable Frequency) chart for today for Southern California -- if we are lucky maybe 3oM. Strange times as checking the MUFF used to mean something entirely different.]

Perhaps some blog readers belong to clubs that have donated gear for sale and so could you possibly check that for me as well.

Another bust yesterday with the rebuilt ZIA as 20M was dead as a doornail. I would hope we get some sort of an opening so I could at least evaluate why it was in the back of the closet. It puts out about 4 watts, and I certainly can hear weak signals from my signal generator -- but a couple of on the air QSO's would open the door to the mystery.

I keep looking on eBay and some of those who post on there must be smoking hemp rope. I saw an Atlas 215X listed for $1700 and most of the Heath Monobanders are around $200 with shipping and many of those are pretty beat up.

Many other vintage 1960-1980 rigs are listed for more than they originally cost. Sold as is, untested and/or for parts or repair, that is a real pig in a poke.

This pricing situation with beat up Boat Anchors must lead to some interesting marketing decisions by current manufacturers. If the prices on old junk are high that opens the door to overpricing new stuff. Just Think $1700 for an Atlas or $1200 for an ICOM IC7300 that could be priced at $1100 and still make lots of money.

Hans Summers is selling a built version of his new QRP SSB transceiver for $185. This product the QMX Plus was showcased several weeks ago at FDIM. His Company QRP Labs has been churning out products that are well designed, work well and by comparison cost pennies. 




I would have to seriously ask why I personally would want to buy a single band 20-year-old MFJ SSB transceiver that cost more ($205) and has less capability and whose market value is less after it has received the N6QW customization. It is all about economics.

In case you didn't believe me here is that $1700 Atlas Radio.


Again, you have some great options such as the QMX Plus or even homebrew a rig. 

In my case I have a penchant for doing the weird like installing a Digital Display in a Heathkit HW-101 or converting the Model 540 Analog Ten Tec Triton IV to the Model 544 Digital Triton IV or building a rig inside a Champagne bottle. I just have a vision of a Monoband Heathkit SSB transceiver with the JF3HZB dial (and digital LO) in place of the drifty stock Analog VFO. Help N6QW achieve that goal.



Them that know can make things go.

73's and TT
Pete N6QW

In case you are keeping score...

 Interesting results... Iowa : Joni Ernst's Republican seat was won by Democrat Josh Turek. [senatordb.com] , [ballotpedia.org] Kansas :...