Monday, July 7, 2025

Summer reflections.


With the 4th of July behind us, I should share as a kid that I also found the 4th to be a somewhat sad milestone. Summer vacation from the rigors of attending school was headed on the downward side. In no time it would be time to shop for flannel shirts, heavy socks and winter coats. Gone would be fresh corn on the cob and watermelon. It also meant soon no enjoying sitting on the back porch and watching the fireflies. We are headed on the path to winter. The longest day of the year (for sunlight) has passed too!




Project X Home Power Supply

I managed to acquire the schematic for the Project X home power supply and some information in that design is noteworthy. 

A Tribal Knowledge Trick is to use a center tapped secondary winding on the power transformer where the that winding feeds a bridge rectifier and the center tap provides about 1/2 the voltage. In our case if the secondary was 500 volts (250 Volts either side of CT) then the bridge output would be 700 VDC +. Here two VR tubes in series through the dropping resistance provides 258 VDC regulated for the screen supply. [OA2 = 150 Volts and OB2 = 108 Volts: Total 258.]

Also in this supply is a 3PDT relay that is triggered off of Pin 4 on the Power Plug which is connected to the PTT button on the microphone. One set of relay contacts are for turning on an external linear amp. A second set on receive grounds the Speaker Voice Coil but on transmit sets the operating Bias (-60 VDC). 

You might ask why the relay on the Bias? With the 4.7K 1W resistor floating (on receive), the bias value is way higher than the Bias level needed for normal operation which effectively cuts off the 8042's. But upon grounding of the resistor the bias level goes to the set value to produce 50 milliamps of idling current.

The last set of relay contacts connects the 3.2 Volts to the Filament Circuit.

The 12.6 VAC is converted to 12.6 VDC to operate the Solid-State and other Electronics in the radio and supply this relay. One additional relay will be included to switch on the main power, so we don't damage the power switch in the radio.

The feature to use instant on final tubes, does place a significant burden on current users some 65 years later to provide the voltages needed to operate the radio. It also makes it difficult to just swap in one of the generic supplies from Heath, Swan or Drake... you'll kill the finals if you do!

Them that know can make things go.

73's
Pete N6QW

Sunday, July 6, 2025

Powering the Beast

The project cluttering my workbench (Project X) has many challenges ranging from actually getting it to work to how do you power the beast.



Tempo One FP-200

Weird and Strange are two really good words. As advertised Project X can be powered from a home (AC) supply or mobile from the DC Supply. In either case the HV is 750VDC, the LV is 210VDC, the Bias is -60VDC, the Filaments are 3.2 Volts at 3.2 Amps and 12VDC at 1.5 Amps. 

So, at the N6QW Radio Ranch, I have a Heathkit HP-23, Drake AC-4, Drake DC 3, Collins 516F2, Collins PM2, National NCXA and a Tempo One FP-200. While all of these supplies cover some of the requirements of Project X, none is a drop in.

In looking at the herd, one supply is left over from a project called Resurrection Radio where I took a Tempo One (worse shape than Project X) and brought it back to life. I bought a FP-200 to power that radio and when I sold The Tempo One, I kept the FP-200 JIC that someday it is needed. Well, some day is here. 


Resurrection Radio

The FP-200 will need some modifications to even come close but most of the mods are reversible and in fact in some cases improve the operation.

The 1st mod is the 117VAC input to the supply. I noted that the Project X power connector on the back panel for switching on the power supply was physically shorted. Oh, Oh I undid the short and the switch is OK. There is a function switch on the front panel that turns on the power supply, has an operate position and tune position. The switch is like that on the KWM2 where it is ganged on the shaft, it is an ON-OFF switch much like on a volume control. To replace that little switch is almost an impossibility.

The solution is to install a power relay in the Power Supply so that the switch in the radio is not seeing a huge inrush current thus increasing the likelihood of a failure. This solves another problem in that the FP-200 had a hot chassis since it was a two wire and not three wire like today's standard. It will be converted to a three wire.

The 150 VDC supply on the FP-200 is not used.

At 600VDC on the plate you will not see 100 watts output, but I can live with that as it will give something north of 50 watts which is OK. The LV supply at 300VDC is too high and my solution is to install two power resistors, one in each lead going to the LV bridge rectifier so the voltage supplied to the bridge is less than 270 Volts AC. 

In fact, this is a TKT (Tribal Knowledge Tip) if you did this on the primary side of a HV Plate Transformer where only half the AC voltage is supplied initially and then using an Arduino to trigger a contactor to short out those resistors after a timed interval you have what is called a "stepped start" circuit. The 1/2 voltage on the primary enables the capacitor bank to charge slowly and then get a full charge after a short duration. In this case the resistors are in the circuit at all times. 

The Bias Circuit has no adjustment at the supply so a dropping resistance in series with a pot using the center wiper will give you the -60VDC. The Bias is set so with the PTT tripped and no mic gain the static plate current on the 8042's should read 50ma.

The AC Filament circuit will need to be converted to DC so that now it will supply 12VDC at 1.5 amps. 

The 8402 Filament supply 3.2 Volts (AC or DC) at 3.2 Amps at first was the long pole in the tent until I thought about a packaged supply. Mean Well sells a power supply that produces 3.3 VDC at 6 Amps with a 120VAC input and these can be had for about $12. It is an enclosed supply and small 3X2X1 inch. I might have to do some filtering in the event of hash. OR an alternative.

In the factory AC supply a trigger from the rig operates a relay that actually supplies 3.2 Volts only on transmit. Suppose we use that feature so that a relay inside the power supply turns on the primary power to the Mean Well. The 8042 has a 1 second warm up time so plenty of time as the 3.3VDC at the terminal is less than 1 second. BTW the 8042 specifies the Filament as 1.6 VDC +/- 10% so we are OK with 3.3 VDC as the filament supply. 

There is plenty of room inside the FP-200 case for the added stuff. I also have a small 120VAC to 12VDC at 5.6-amp power module and just may use that versus building a 12 VDC supply from the 12.6 VAC filament circuit.

A Bonus as the FP-200 case has a built in speaker.

Never TRUST what you get! The Project X power connector has 10 Pins and is not a Jones type connector. One pin is broken, and ALL the pins have been touched by a soldering iron.

The Bastard prior owner burnt a lot of the insulation on the wiring to the connector and in one case the wiring didn't match the schematics. Then the dim light lit --- he converted the 3.2 Volt input with the 8042 tube filaments in series to a parallel connection thus needing to supply 1.6 Volts at 6.4 amps. Thankfully the power connector appears to be the only place where there is the obvious touching with the 80-watt Radio Shack soldering iron. 

Thus, today we covered the power supply, and the modifications needed to the FP 200 so it can power the Project X transceiver.

Them that know can make it go.

73's
Pete N6QW

Saturday, July 5, 2025

Nostalgia Time

A Trip Back in Time. My middle son, Tim and his lovely Amy visited yesterday as we celebrated the 4th of July. Several visits ago, Tim mentioned some items that were of his childhood that might be lurking in about 10 boxes of stuff that were in the move some 12 years ago. These were stored in my garage and yet to be opened some 12 years later. At the time of the prior visit, we set July 4th as the date to open the time capsule.

We didn't find the stuff he had on his list but did find a whole box of family photos that were not collected with other photos I have. 

Concurrently, with the passing of the XYL, there are some legal matters I had to revisit and just last week in a meeting with our lawyer, she asked a rather strange question seeing as we had been married for 57 years. She asked me was it a Happy Marriage. My quick answer was no one sticks around for 57 years if they are unhappy. 

But in looking at those photos which actually spanned some 40 years my answer is more than just sticking around -- it is an affirmative Yes. I focused on facial expressions. If someone is unhappy it will show in the photos. Conversely, joy is hard to hide. Firstly, those photos affirmed the XYL was sure hot looking (an important criterion being Italian). But more importantly I can see in those photos her commitment to the family. There were the usual birthday party photos of the kids, and you could just clearly see the proud Mom. 

So, the 10-box opening yesterday was not a simple act of finding some old junk but instead brought closure in the sense... it was a great run!



The 8042 Vacuum Tube is a 6146 in disguise and a rather odd duck. The filament voltage is 1.6 Volts (AC or DC) at 3.2 Amps. It has an "instant heating" filament taking but one second to light up the fire in the wire and you are good to go. The SDR guys will call that a terrible latency. But for portable equipment it conserves power. A startling revelation as a NIB matched pair on eBay can be had for about $20.

The Project X transceiver has a pair of these and so you could be mobile in a parked car where in the receive mode the rig draws really low current and hitting the PTT turns on the DC-to-DC inverter to produce the high voltage and provide filament power. Read Drain the Battery. Many pieces of hybrid equipment of the 60's era had a switch to actually turn off the filaments (SBE-34 and Yaesu FT-101). 

Now another twizzle, an innovation, as the Project X rig was a hybrid rig but the only tubes were 8042's which were off during receive. There was no tube driver circuit. Sufficient drive power came from three transistors in the driver stage.

There is a listing on eBay under Hallicrafters for a military SSB radio called the SBT-100 (AKA The Village Radio). This radio uses an uncanny look alike three transistor driver stage. So, who stole from whom? The Village Radio was a product of the Vietnam war where these radios were given to the village chief who was supposed to report Viet Cong activity. It is suspected this was a CIA brainchild who failed to recognize the village chief was the Viet Cong. Take the smile off you face Project X is not an SBT-100. The SBT-100 is a 6 Channel SSB transceiver that would be ripe for a JF3ZB + Si5351 conversion.




How did you do on yesterday's citizenship test? Yeah, that was sneaky to not have Vermont as one of the 13 Colonies. Speaking of that there is some stupid event with ham radio where stations are located in the 13 Colonies and if you contact all 13 you get a free case of dermatophytosis.

Them that know can make things go.

73's 
Pete N6QW

Friday, July 4, 2025

Happy 4th of July!


Rear View: A Naked Project X!

About a year ago on December 7th, I happened to mention to a 20 something hottie cashier at the local Albertson's that it was Pearl Harbor Day. She asked --- what is that? If we asked that same age group what is the 4th of July, you might get an answer: "The day Tik Tok went live".


To put you in a festive mood and test your Americanithcity (ethnic American) here are a few sample questions from the US Citizenship test.

1. Ben Franklin had a day job and the 1st to hold this position and what was it? [No don't ask who was Ben Franklin? He was quite the ladies' man and was known to romance older women and his reasoning was: They don't swell, they don't yell, they don't tell and best of all they are as grateful as Hell!]
2. In what year was the US Constitution ratified?
3. The 1st 1o Amendments to the US Constitution are known as ...
4. What pivotal role did Thomas Jefferson play in the formulation of the US Constitution.
5. Who was President when the US entered the Great War? [It was not called World War I because we did not know about WWII at that time.]
6. What was his stated reason for doing so?
7. How many stripes are on the US Flag?
8. Which one of these is not a part of the original 13 Colonies. Massachusetts, New York, Vermont, Georgia.
9. Who is responsible for making the laws of the land?
10. What is Habeas Corpus?

Answers:

1. Postmaster General
2. Adopted in 1788
3. Bill of Rights
4. That item #3 be included in the Constitution
5. Woodrow Wilson (1912-1920)
6. To preserve Democracy
7. Thirteen
8. Vermont
9. Congress
10. Meaning show the body as in Due Process to prevent unlawful and indefinite imprisonment.

Regrettably, in 2025 we have individuals who want to change these answers, especially for items 9 and 10.

Our photo today of Project X is my unit with the cover off. The photo in the prior posting was of a National NCX-1000 and meets some of the criteria: Dirty, Off Brand and not many produced. My prior National rigs SW-54, NCX-3 were not very good! The NCX-200 and NCX-5 were better.

Them that know can make thigs go.

73's
Pete N6QW

Thursday, July 3, 2025

The Project X Assessment Process

The Assessment Process must start with a realization mindset and here are some critical points for consideration.



Starting the assessment process!

(This is not the X rig, just an example of what might be a starting point.)


1.  The project radio is over 60 years old.
2. It was an off-brand rig with really low production run numbers, perhaps less than 500 units' total. It is estimated that less than 20 staff worked at this company. I believe my unit was in the 1st 50 units produced (#44) so expect the worst.
3. To keep costs down the components selected for the build were the absolute bottom of the barrel and the design reflects non-standard approaches and applications built around the low-cost parts at hand.
4. Unlike Swan or Yaesu gear there simply are not spare assemblies and mechanical parts or things like meters, knobs, switches or solid-state devices up for auction on eBay.
5. There are no You Tube videos, Product Reviews or group.io forums. The company folded and was literally a one man show. Two hams have been identified who have restored this rig so there is somewhat of a limited knowledge base that can be tapped.
6. The photos I have seen of this radio definitely support not putting this radio in the kitchen sink for a scrubbing and then the oven bake, followed by the sun-dried tomato process. This brings up another point regarding cleaning as likely any front panel lettering must not be subjected to ANY chemical as there is a high risk of destroying the lettering.
7. One arduous task is to take the schematic and identify every part and its actual physical location. I recall once on a Hallicrafters SR-150 restoration where the schematic showed a RF choke. Based on the circuit where it was used, I thought it was missing only to find it was 10 inches away installed on a terminal strip on the back apron. This is the time to find wires that are floating and only connected on one end.
8. Decidedly the assessment should flag any solder joints that look like they have been touched. Look also for discolored parts (burnt resistors) or leaking electrolytic caps. Since most of the rig is solid-state, I suspect capacitor issues more so than out of spec resistors. Another dimension to the assessment is to sort the task into two piles: 1) Cosmetic and 2) Functional. Priority rests with the Functional. New cabinet feet will round out the overall appearance but are not required to make it work functionally. 
9. Many of the tunable inductors are non-shielded coils sitting out in the open and easily damaged and NO replacements. Extreme care must be exercised when working in, on or around the chassis.
10. In summary, there is but one chance to restore this radio and applying power is NOT one of the 1st things to be done. Thus documentation, photos and careful note taking plus having an actual restoration plan is mandatory before doing any work on the rig. Don't be hasty when buying parts, like don't buy the 1st substitute replacement part you see -- there is the same part 70% cheaper elsewhere on eBay.

At some point I likely will ask myself was this a really good project to undertake. Fools rush in with the intent of getting the best seats. Engineering analysis is critical to keep costs in sync with what the ultimate desired state is envisioned.

Today's Project X Clue. The finals are in the 6146 family of tubes, more than QRP!

Them that know can make things go.

73's
Pete N6QW

Wednesday, July 2, 2025

Project X

Bigger than a Shoe Box but smaller than a Bread Box, a unique renovation and restoration project of an obscure vintage radio. Few actual units were built or even exist. This project is a personal skill challenge for me and only undertaken because now I have some time. So, strap in for some really boring stuff over the course of the next 3 to 5 months.


The "noodling process" and rig assessment will take about a week, thus infrequent updates of the blog... but worth the trip and the wait. Stick with me as you will love it.

Them that know can make it go!

73's
Pete N6QW

Tuesday, July 1, 2025

How should I approach Homebrewing a Radio?

[Late yesterday afternoon a package showed up from Home Depot. I hardly ever order anything from Home Depot since the store is only 2 miles from my QTH. I checked to see if it was mis-delivered but it had my name on it. Surprise! It was a bottle of Krud Kutter and I have no idea who sent it to me. But a Big Thank You!]


This is a question often asked as if there is some exactly right and only way to do it. Well, surprise there is no singular answer. No matter what way is chosen the care with which it is done, and the observance of good practices are the keys to success.

The big orangutang in the tent is the use of through hole versus surface mount components. The final test is: does the same circuit schematic provide the same performance level with either type of component. In 99% of the cases there will be no difference. The other 1% may cover issues of shielding, compactness and heat transfer.




So, it gets down to the comfortable shoe's response. Going on a hike with a brand-new pair of boots risks blisters while the old reliable pair of boots just keep on walking. It is a comfort zone thing. Those of us with FFS have a hard time holding on to or maneuvering those teeny tiny parts. 

Most of the time SMD needs a circuit board whereas Ugly or Manhattan requires nothing more than some pads and superglue. We are always on the quest of "get er done" and that seems easier using through hole and some ugly pads. The sophisticated name is "Rapid Prototyping".

The basic tenet is that it does not have to look good to work well. There is another factor here in that most of the time homebrewing a rig is an evolving process where circuits are tuned and tweaked many times before a final configuration is achieved. Harder to do with SMD as soldering/resoldering can lead to destroyed parts.

Let's face it, SMD really shines on a production line where parts are installed using pick and place manipulators. Manual installation of SMD parts on a board is more Black art than a science. However, the photo above suggests that SMD can work well for home brew projects, and it even appears the circuit board was made using a Dremel tool or a CNC with a dull engraving bit.

The other piece is cost. More and More through hole parts are being shifted to Surface Mount. SMD parts are surprisingly cheap and as less through hole parts are being made the costs increase accordingly. Back to our comfy boots example. New heels and soles on our old boots may approach the cost of a new pair of boots. But with the repairs the old boots are the choice as they are broken in and no blisters. But that is a conscious decision made by the homebrewer

Earlier I mentioned the execution of process, thus with through hole and SMD you still need proper solder joints, circuit layouts that avoid unwanted feedback, and always with an eye toward serviceability. These apply in all cases.

On the record, I use both through hole and SMD parts. But I also design my circuit boards that are cut on my CNC. The boards I design are more universal in nature using a modular approach. If I want an audio amp, I pick a place on a PCB, call up an audio amp design and push the start button. No pad glue downs, as I invested the time in the module designs. Same thing for an IF Module or bilateral amp stage. Pick a place and mill away.


The above photo shows the Mic Amp, PD/BM, IF Module, Rx Tx Mixer and BPF. All are individual modules on the CNC ... Pick a place and mill. The board contains both through hole and SMD (ADE-1's).

So, my way is not THE singular way, and it all gets down to your comfort zone.

Them that know can make things go!

73's
Pete N6QW

In case you are keeping score...

 Interesting results... Iowa : Joni Ernst's Republican seat was won by Democrat Josh Turek. [senatordb.com] , [ballotpedia.org] Kansas :...