Tuesday, August 26, 2025

Initial Testing of the new DC Power Supply.

Later today my new $30 power supply is scheduled to land at my front door. The supply, a switcher, is rated at a wide voltage range input, and supposedly good for 6.3 Volts at 5 amps and 300 VDC at 300 milliamps. Targeted at vacuum tube audio circuits, it is touted as low noise.



Before I place all eggs in one basket, I thought it best to do some lab testing and this led me to thinking about test criteria and the actual conduct of the tests. I also generated a concerns list.

The first is the price and to put it in crass terms what would you expect from a $2.50 hooker? The price of $30 for the supply raises that same level of concerns.

Basically, we heard some good things about this switcher, but I do wonder if the glowing reports may belie that there have been known component failures in the supply. Gasp were those glowing reports AI generated?

If it fails at plug in, then we know the awful truth thus there should not be a mushroom cloud of smoke at the 1st application of power. That is followed by a 15 Minute test where the supply is idling (no load connected) where nothing gets really hot, or no burning odors are observed.

Now the big issue is how does this supply hold up under load. The current vision is that most of the load will be seen in the high voltage section and so we should look at some math. 

There is also a power duty cycle factor to consider in that in receive we likely would see a constant load (9 tubes total) but it is in receive where only six are drawing current of less than 70ma.  The max current draw is the PEP of the 12GE5 final on voice peaks and there we could see 200 milliamps or better total current draw on peaks. 

Essentially 300 VDC at 0.3 amps is 90VA. (90 watts). If the load is a 1000 Ohm resistor, then the current is 0.3 amps. That resistor better be 100-watt rated! If the specs hold, then we should see no sag in the voltage and the current supplied should hold at up to 0.3 amps. I don't have such a resistor. 

Now if we would theorize that even at 0.06 amp the supply would hold that would give us a really "good indicator". If it flunks the 0.06-amp test with a voltage sag or failure to supply that current level that is a sure sign it will flunk the max power test. 

Two 10K resistors (20W) in parallel is 5K yielding 60ma with 300VDC applied and only needing 18 watts of power rating. The 60-milliamp current is close to the load that will be seen on receive.  The 2nd part is holding that voltage and current over a 10 Minute period without sagging or smoking itself. This is a critical test as if fails this part ... it fails totally. The duty cycle with SSB voice is easily within the 0.3-amp range and transitory. It is the constant load on receive that is the most demanding.

Other parts of the testing would be to look at the ripple content and noise generation. A DSO will measure the ripple across a series of dropping resistors as you don't want to smoke the scope probes. For the noise I can use my Hermes Lite 2 SDR to look at the noise and evidence of switching transients across the HF spectrum

Now a concern that came up after the unit was purchased. The filament voltage is stated at 6.3 Volts at 5 amps. As a victim of habit, I just assumed that was 6.3 Volts AC, but that could be DC. I could not find that info from the product advertisement. 

Perhaps a hidden bonus is to change over to all 6.3 VDC tubes (the 12Ax7 and 12AU7 can be wired for 6.3VDC) and this would mean I would power the filaments from this single supply and a smaller 12VDC supply could be used for the solid-state circuits.

So, DC would not work with my idea of back feeding a filament transformer for the Bias supply. I might have to add to the mix a small 115VAC to 115VAC transformer for a bias supply. eBay has them!

Things are certainly in a churn, and it is interesting of how other countries view the US. If you have any friends outside the USA, you might ask them. A majority of you voted for this option and was this your expectation.

Reduce your digital footprint as you are being watched.

Them that know can make things go.

73's
Pete N6QW

Monday, August 25, 2025

Sundays when I was a kid back in Pennsylvania.

This past Sunday morning Pasta Pete was at work in the kitchen. I even bought a name tag so when I go to the Grief Group Sessions people know who I am. Should mention that so far, 80 to 90% of the GG attendees are older YL's and the rest are guys like me.  


(I had thought about a 2nd Line: I can cook!)


Back to Sunday mornings in western Pennsylvania. It was a ritual starting with the family going to 8 AM mass at St. Margaret Mary's Catholic Church followed by breakfast at home and then the magic. Everyone out of the kitchen as my mom whipped up Sunday Dinner served promptly at noon. 

There was the homebrew spaghetti sauce with meatballs, breaded eggplant, with a side of zucchini, a tossed green salad with tomatoes and cucumbers and for dessert something out of this world. Supper was usually just a snack as the Sunday Dinner was enough food for a week with the calories to match.

It was not unusual to have midafternoon family visitors where mom would hit the freezer for a previously made dessert to serve to family.

I liked the summer Sunday feasts as the meal was usually served outdoors, and the dessert often was cannoli or an ice cream sandwich made from waffle cookies and a slab of vanilla ice cream. If you check pastapete.com the recipe for the waffle cookies can be found along with a how to do it you tube video. Also on the website is the magic spaghetti sauce recipe.

Those were funny times as the Sunday ritual was watched by others. If you were not at 8AM mass with the whole family, it was like the Spanish inquisition. One Sunday I was on a trip, and my mom got a call from a "Nosey Nellie" wanting to know if I had stopped going to church.

As my sauce came together, and the rich aroma of the simmering onions and garlic permeated the house it was a stark reminder of some really great past times and the impact of a simple family meal. 

This past Sunday it was just me eating spaghetti and vegetables and the cannoli has given way to 70 calorie Non-Fat, Low-Fat, No-Taste, Small Portion and Strange Appearing Danon Yogurt. [Sunday Mass from our local Catholic Church is live streamed on YouTube. Times do change!]


Potent: Olive Oil, Onion and Garlic, Hot Pepper

On Sunday I did write a CNC program for the panel meter cutout, and I bought a DC power supply for the Hybrid Wireless. This supply will provide 6.3 Volts at 5 amps and 300 VDC at 300ma. It should be enough juice to provide 20 or so Watts of RF output from the 12GE5 Final. The price is less than $30.




This supply will be used along with a 12 VDC 5.6 Amp power supply board that will source the SS circuits and handle the filaments. The 6.3 Volts will be used to reverse feed a 110VAC to 12VAC filament transformer which then will produce about a -60VDC for the bias. This will make for a much smaller footprint and perfect for this rig.

Hide your digital footprint.

Them that know can make things go

73's
Pete N6QW

Sunday, August 24, 2025

Pox on Home Depot!

As I continue the work on the Hybrid Wireless metal bashing, I will need to cut some aluminum plate using a hacksaw. One piece of stock I have as it stands is too large for my CNC but once cut, I can true it up using the CNC Mill. The problem is the 1st cut and the need now for some fine-toothed hacksaw blades. 


Being Saturday, I needed to run some errands and one place I had to visit was very close to the local Home Depot. So, I get to Home Depot and find the Tool Section and the hacksaw blades... $6+ dollars for two blades made in China and likely good for one cut in soft metal before going dull. (I did get a lot of steps on my Smart Watch so that was good.)




Finally, you get to the checkout area where there is an array of self-service terminals and no manned cashier stations. There are some terminals that only take cash and some that only take credit cards. I opt for the cash as there is my internal discipline to leave no digital footprint, so I wait for a cash terminal to be available.

I hate those machines as they always seemed to get hosed up. This morning was no exception! I scanned the code, and it read OK and the price with tax was $7.48. I opted for cash and was instructed to introduce the cash into the slot. 

I had at the ready $5 and three $1 bills. I put in the $5 and then a $1 and then the machine shuts down. I use the touch screen to call for assistance and waited about two minutes for someone to show up. 

The attendant showed up and did all sorts of things with various keypads which did nothing and then unlocked another cabinet to secure a key to open the machine and then unlocked a box that was the cash repository where she affirmed the last two bills put in the machine was a $5 and a $1.

She then says we have to go to a special terminal where she scans the hacksaw blades and puts that transaction on hold, while she goes over to a special manager's terminal and gets into a cash drawer where she removes $6 and hands it to me. Then she says put your $8 into the slot and I told her NO. You do it! She did and I got 52 cents in change, two hacksaw blades and a receipt.

So, then I asked her what happened, and she says I don't know, but it happens all of the time. The total elapsed checkout time was 15 minutes. Unless it is a dire emergency that is the last time I will go to Home Depot. 

I hate those machines and their lack of efficient and reliable operation. The same for my grocery store as it is hard to checkout items like fruit and vegetables. If everything is bar coded, then maybe not as big of a problem.

This will only get worse, as more AI is introduced under the guise of speedy checkout with attendant layoffs of people who would actually check you out. 

In the end I had to have a real person finish the transaction for $7.48 and took 15 minutes of my time. There is not one blog readers who is reading this that did not have a bad experience with these AI checkout machines. Shudder to think if I had used my credit card!!!!!!!

Did install some additional angle stock on the base plate but it was 90F in the garage, so I stopped.

Them that know can make things go.

73's
Pete N6QW


Saturday, August 23, 2025

Travelog: A visit to the Academy Museum 0f Motion Pictures

A non-radio day yesterday, the local family, son Tim, his XYL Amy and daughter Gina had a fun-filled outing in LA. The first stop was lunch at the Farmers Market (3rd and Fairfax) followed by a tour of the Academy Museum of Motion Pictures located close by.

N6QW behind the Godfather's Desk

Museum highlights included sets from various movies, including models used in filming of movies like 2001, The Space Odyssey, Star Trek, Barbie and of course a desk from The Godfather.

Many costumes used in the movies were on display and that was a treat to see a photo of a movie scene right next to the costume.

A large tabletop computer generated display was a map of the LA area showing the various studios that literally ringed Los Angeles. A factoid was that in 1902 when the movie business essentially moved from New York to LA the reining industry was oil. In 1929 LA had grown 12X and the driver was the movie business which replaced oil as the industry. 

At its heyday LA had over a dozen major studios. Some studios were owned by major actors. Something I never knew was that actor Sessue Hayakawa who was the Japanese Prisoner of War camp Commander in Bridge on the River Kwai actually had been making movies in Hollywood since 1914 and owned Haworth Motion Picture Studio. BTW although born in Japan he was a graduate of the University of Chicago.

A technology old dog new trick was Pixar Animation which was a series of small character figurines arranged on a circular disc which was spun up at high speed. A blur indeed. Then they turned on the strobe lights and it was an animated show. Can anyone remember the strobe light kits used for car repair? Stop motion technology used for movie making.

A fun day being with family which started with my Friday visit to the cemetery to bring flowers to my XYL. My smart watch gleefully announced by about 5PM, I hit 6000 steps.

Many may be questioning my continual admonition about all of us being monitored, observed and watched. You need only to call up the Microsoft copilot app and type in your name and call sign and see what results. In short order you will see anyone can do this. Reduce your digital footprint. One thing for certain never say negative things about old what is his name. If you do, your name goes on a list.

Them that know can make things go.

73's
Pete N6QW 

Friday, August 22, 2025

Bashing Metal

In today's world, homebrew frequently uses pre-made circuit boards or that awful ugly unsightly approach with superglue and small copper squares.

When I started homebrewing in the 1950's the soup du jour was an aluminum chassis and the use of Greenlee punches for cutting the holes for the Tube sockets. This was frequently called "metal bashing".

If you want to do a bit of bash and mash start with the type 3003 or 5052 aluminum as these are the variants that are easy to mill, drill, hammer and beat. The type 6061 is not too good for working with simple hand tools.

I had a meeting with myself yesterday and decided to use a base plate of 12X8 inches as I found I had two pieces that were 1/8 inch thick. One piece will serve as the main chassis plate and the second piece will be the bottom plate. I also have a 12X12X1/16-inch piece of aluminum stock that I will cut in half so that the front and back panels will be two pieces 6X12 by 1/16 inch thick. Indeed, metal bashing.
 
 
 
 Top Plate Layout
 
Underside Layout

In an earlier post I mentioned the use of cardboard cutouts, and this is where they come in handy to allocate real estate on the mounting plate.

The bash part went pretty quickly but the measure 300 times and cut once took longer.




The use of 1/2 X 1/2-inch angle stock ties the front and back panels to the base mounting plate as well as the bottom plate. Angle stock at the very top of the front and back panels tied together with cross pieces rounds out a box like structure. Very rigid and solid!






Basically, we positioned the nine-tube chassis and located 4 holes where I installed the mounting pillars, so the tube chassis is elevated above the mounting plate. I also located, a 1.125 inch in diameter pass through hole so cabling can pass to the underside where the power distribution board and the audio amp board will be installed. Also on the underside is the Driver, the IRF510, and Low Pass Filter.

Other controls such as Power On/Off, MOX, mic input and mic gain, carrier balance and the audio output will be on the front panel at about .75 inches above the bottom plate reference. 

The 12GE5 will be located along the right side of the chassis as will the Plate Tune and a RF Output Meter. 

Reduce your digital footprint. Things are not looking good on the horizon. It seems like an important Republican operative was raided by the FBI. A coincidence? The signs are clear.
 
Them that know make things go.
 
73's
Pete N6QW 


Thursday, August 21, 2025

Hardware Fabrication

C'mon you belong to all of the obscure social media sites, you have the latest iPhone, and Smart Watch, two FT710's and matching Mercury Amps, an 84-inch wall mounted TV with 500 channels and gasp you even voted for what is his name... yet you don't have a CNC Milling Machine.


Yesterday I spent a bit of quality time fabricating boards for the new Hybrid Wireless Set made all the easier because I have a CNC Milling Machine. No messy super glue and cut copper pads, just chuck in a blank board and push the start button. 

The additional advantage of the CNC is the board layout is standard and pays attention to preventing unwanted feedback loops, provisions for heatsinks and standard mounting arrangements. I would rather spend my bench time soldering parts to a board versus trying to unstick my fingers or remove superglue from my fingers so I can use biometrics with my smart phone. 


Two BPF's and an IRF510 RF Amp

According to a guy who should know, he stated that smart phones are dead! Gee, you just downloaded an app that tells when your Girl Friend might get pregnant. You don't need that app if you are homebrewing radios using your CNC machine.

Them that know can make things go. In a prior blog post the schematic for the BPF's was shared. The IRF510 is a standard design and can be found throughout the n6qw.com website.

73's
Pete N6QW


Tuesday, August 19, 2025

Fabricating two Band Pass Filters for the 20M Hybrid Wireless

In the development of the original 40M Wireless, I purposefully used two separate Band Pass Filters. The original Swan 120, which was the template for the wireless it had tuned coils. I converted that part of the design to broad band with the BPF ahead of the 12BA6 RF amplifier stage

Another innovation was the use of a homebrew 2.5 mHy ferrite core choke in the plate circuit of the 12BE6 transmit mixer where a couple of turns of wire on the FT-82-43 core provided a 50 Ohm tap point. From this tap point the transmitted signal passes through a second Band Pass Filter and on up the RF transmit chain.


A simple mod to the 40M Hybrid Wireless gave proof of life that receive on 20M was quite good. Two more changes are needed to prove 20M transmit and these include a 20M transmit BPF and the 20M LPF following the genuine IRF510's (from Jameco... no BoJack's here.)


This design uses 9-50pF Trimmer caps available from Jameco Electronics. If you parallel a 150pF cap with C1 and C2 and replace C4 with a 5pF Trimmer cap this can be tuned to 40M. Note R1 is for the simulation and not installed as hardware.


20M BPF

Our LT Spice simulation reveals a nice flat response across the SSB Phone band and so this design should do well in the 20M Hybrid.



Using an existing stored CNC program about 5 minutes of work created two PC boards for the new BPF's. That is on the agenda for today's work.

Hide your digital footprint as we are all being watched.

Them that know can make things go.

73's
Pete N6QW

In case you are keeping score...

 Interesting results... Iowa : Joni Ernst's Republican seat was won by Democrat Josh Turek. [senatordb.com] , [ballotpedia.org] Kansas :...