Tuesday, September 2, 2025

It is not Gobal Warming

It is just plain HOT! For most of yesterday afternoon the garage was at 90F and the next 10-day outlook is SOS. (Same Old Stuff).


But I did get some things sorted out and that was to install the octal socket on the integrated power supply board and installed the two Band Pass Filters and laid out the locations of the Driver, IRF510 and the Audio Amp on the underside of the mounting plate. This took a lot of time to ensure mounting holes on one side did not end up square in the middle of a pc board on the top side. I did find a solution, but it was measuring 300 times and cut once.

Final Layout of the Power Supply I/O Panel.



Rearranging the 300VDC Supply opens up space for the Bias Supply.


Locating the Tx and Rx Band Pass Filters.

The fitting of the five boards (2 on top and 3 on the bottom) was not unlike the 1st time fitting Mary Jo at 136.36 KG or 21.43 Stone weight (300 pounds) into the back seat of the 57 VW Beetle. Many tries but finally successful. The KG weight and Stone weight is provided to our international blog readers to whom pounds is not a standard. No matter the weight form, she was hefty!

I am also pondering and somewhat fretting over the cutting of the front and back panels as I don't want to screw up the surface finish and the general layout so ergonomically and aesthetically it meets the highest standards. I have done some practice cut outs on scrap material and some of those are plain ugly, so I continue to fret!

We continue to make progress and foresee about another two weeks hampered mostly by the hot weather.

Them that know can make things go. You are being watched.

73's
Pete N6QW

Monday, September 1, 2025

It is Labor Day, a national holiday in the USA

I have no background history of the why of Labor Day other than to recognize the strength of one of the greatest US assets, its people and the labor movement. It was the projection of that special resource during WWII that made the US "THE" world leader.

An article today on the internet, suggests a view that the world leader has shifted to China. A questionable view but a somewhat nagging view since the internally it appears to be we are now a nation dedicated to partisan fighting and revenge politics. 


But today I want to focus on homebrew and supply a little bit more "labor" to Hybrid Wireless project. It was hot in the garage lab yesterday so just a small amount of work where I built the rear panel for the integrated power supply. I still need to add the octal socket that will be used for the Hybrid Wireless power cable connection which will be located above and slightly to the right of the fuse.


Power In / Out Panel

A blog reader taking advantage of AI prepared and sent to me a design for the 540 VDC supply that used no power transformer. Now this was interesting as I immediately thought of a 450VDC power supply used in a ham rig in the 1960's that used no transformer, more on that later.

The AI design starts with a 48VDC switching power supply and then using a booster circuit ups the output to 540 VDC. I can see the merit of such a circuit being light weight, small size and great efficiency. There was some definite rationale in going from 48 to 540 a 11X boost versus a 12 volt which would be 45X boost.

I have the transformer and most of the circuitry is in place and only need the addition of the bridge rectifier (Four 1N4007's), the 100Ufd @ 600 VDC electrolytic cap and a 30K 10-watt resistor to complete the supply. BTW AI even prepared a BOM with part sources.

Now back to the 450VDC no transformer power supply. The rig was the SBE-33 that took the 115 VAC mains input and using a voltage quadrupling scheme (no transformer, only diodes and caps) to produce the plate supply for the 27GB5 Finals. Want to go mobile... a 12VDC to 115VAC inverter. That was 62 years ago. BUT it was also a shock hazard and an NE-2 on the back panel told you when you had to reverse the two-pin power plug.

Them that know can make it go. 

Noteworthy many Americans think ICE and DHS are our greatest assets today because of the touted "millions" of illegal aliens that have been deported. That begs the question of the metrics being used to assess greatness as a nation. Such metrics would likely not list deportations as being the top criteria.

73's
Pete N6QW

Sunday, August 31, 2025

Building a 450VDC Power Supply.

How to design a 450VDC at 0.1-amp Plate Supply for the 12GE5? Copilot jumps in and gives an opinion.




Today
Full wave Bridge power supply: 520 VAC, Choke Input at 10Hy, Filter Cap 100 Microfarad at 500 VDC. Bleeder resistor 10K. Is this OK?

You're working with a pretty serious high-voltage power supply setup, so let's break it down and assess whether it's safe and functional:

⚡ System Overview

  • Input Voltage: 520 VAC (RMS)

  • Rectifier Type: Full-wave bridge

  • Filter Type: Choke input

  • Choke: 10 Henries

  • Capacitor: 100 µF rated at 500 VDC

  • Bleeder Resistor: 10 kΩ

✅ What Looks Good

  • Choke Input Design: This is a classic approach for high-voltage supplies. A 10H choke provides strong filtering and helps maintain continuous current flow, which reduces peak charging currents and improves regulation.

  • Bleeder Resistor: A 10kΩ resistor is reasonable for safety. It will slowly discharge the capacitor when the supply is turned off, helping prevent electric shock.

  • Capacitor Value: 100 µF is a decent size for smoothing ripple in a choke-input filter. It won't overburden the rectifier and will help stabilize the output.

⚠️ Potential Concerns

  • Output Voltage Estimate: With a choke input, the DC output is roughly 0.9 × RMS input. So:

    • 0.9×520 VAC≈468 VDC0.9 \times 520 \text{ VAC} \approx 468 \text{ VDC}

    • Your capacitor is rated at 500 VDC, which gives you only ~7% headroom. That’s tight. If your line voltage spikes or the choke saturates, you could exceed the cap’s rating. Consider upgrading to a 600 VDC-rated capacitor for safety.

  • Bleeder Power Dissipation:

    • At ~470 VDC, the 10kΩ resistor will dissipate:

      • P=V2R=470210000≈22 WP = \frac{V^2}{R} = \frac{470^2}{10000} \approx 22 \text{ W}

    • That’s a lot of heat. You’ll need a high-wattage resistor, ideally 25W or more, possibly mounted with a heatsink.


I will change the Bleeder to 50K and upsize the Voltage Rating on the Filter Cap to 100UFd at 600VDC and this should do the deed. The Panel Meter reads 0 to 500 VDC.


Integrated Power Supply Front Panel

Started work on building the supply and this is what it will look like.


Power Supply for the Hybrid Wireless

In the photo above, along the left side is the 520VCT power transformer and 10 HY choke. The blank PC board will have the Bridge rectifier installed and pad connections for the choke, plus installation of the Filter cap and he Bleeder. That I built yesterday.

Along the right edge is a 12VDC 5.6-amp supply and at the back our 280VDC 0.3-amp supply. 

The Plate Transformer has a 6.3VAC winding which will be used to feed the 12.6 VAC side of a filament transformer rated at 1 amp and pretty small (not installed as yet). This will provide about 60 Volts AC at the terminals normally used for the Primary.

My plan is to add a back panel and mount small filament transformer on that vertical panel and that becomes the Bias Supply at -60 VDC. The Bias Set Pot will be on the Hybrid Wireless Chassis.

The back panel will also contain an 8-pin socket where all of the voltages required by the Hybrid Wireless will be connected.

1. Power Switch
2. Power Switch
3. 450 VDC
4. 280 VDC
5. -60 VDC
6. 12 VDC Filament
7. Ground
8. 12 VDC Relay Supply 




Close up of Bridge Rectifier PC Board
(Parts to be added when they arrive)

A Final Act will be to put some sort of enclosures around any exposed high voltage portion of the circuitry. I have a couple of ideas in mind that will eliminate any potential shock hazards.

Them that know can make things go.

Old what is his name was MIA for a couple of days and has reappeared so to all watchers just a blip on the radar. It is an interesting cultural phenomenon; you are the news even when not making news.

73's
Pete N6QW

Saturday, August 30, 2025

The Front Panel ~ Hybrid Wireless

Not unlike the Final RF Cage, a lot of effort will be put into the layout of the front panel. It all started with the 12X12 Inch 5052 Aluminum panel that I cut into two pieces 6X12 inches. I took care in the cutting using the Home Depot newly acquired hacksaw blades to cut a straight line and then went to the CNC mill to true up the edges and to make matching pieces. Along the way I ran the X Axis past the stop and had to do some CNC Mill maintenance work to get that back working properly.  That consumed most of yesterday.


Suddenly it became apparent that I needed to rethink the front panel layout as 6X12 is 72 square inches seems like a lot. However, we do have a large tuning knob, a very large display, five knobs, three toggle switches and two audio jacks (Mic and Speaker) and finally a panel meter. 

Key to the layout is ergonomics and not getting cables in the way of the critical controls like main tuning, audio output, transmit controls like mic gain and Final Tune. Time for the cardboard cutouts.

Still another factor is that the main assembly plate will sit two inches from the bottom and four inches from the top. I may even have to cut a notch in that assembly plate to accommodate the optical encoder. If you look at your KWM-1 or KWM-2 or some of the Heathkit and Swan gear you will see that notch at the front of the chassis to accommodate the large analog dial. My notch may only be 1inch wide and 3/4 inch deep. But the carboard cutouts will provide the answer.

 Front Panel Ouija Board

The four controls as the upper left are for Volume, RF Gain, Carrier Balance and Mic Gain. The one control along the right edge is the Plate Tuning Cap.

This simple "put the knobs on the front panel exercise" indicates I likely will not need the notch. The open space to the left of the knob would be for the Mic Jack, USB/LSB Select and MOX/Tune. To the right would be Main Power and Audio Output. The 3.2-inch Color TFT would shift to the right to be more centered. 

Mind you a 1/2-inch wide by 12 inches long area at the top and bottom edges is unavailable as that accommodates the aluminum angle stock for the bottom plate and stiffening structure to make the box rigid. 

More work installing boards today which involves more drilling on the main assembly plate.

Oh, have been rethinking the power supply and I found in my stash a 520 VCT 100ma transformer and using a bridge rectifier with a choke input would give me 450 VDC at 100 milliamps and that would be for the plate supply just for the 12GE5. The supposed 300VDC 0.3-amp supply will be for the low-level stages and the screen supply for the 12GE5. 


Them that know can make things go. 


73's
Pete N6QW
 

Friday, August 29, 2025

More Metal Bashing and Precision Locations.

It was hot in the garage yesterday and I took advantage of the heat to sweat off a few pounds. I just sweated but didn't lose many pounds!

Yesterday's work scope was to install the shielded RF Final enclosure, install the 12GE5 tube socket, the Pi Network and line up the area allocation. This singular installation will drive further installations both on the top and underside of the mounting plate. 

I near got a hernia using the chassis punch to cut and 1- and 1/4-inch diameter hole for the 12GE5 in the 1/8-inch aluminum plate. This is where you have to eat your Wheaties.

There was extensive measuring, more measuring and still more measuring before cutting any metal. As a starting place I am using a Pi Network from a Junker SBE-33. The loading cap is a high value padder cap. So, the plan is to set that padder value once and then the front panel Tune Control will bring the tank into resonance. This is like the Pi Network in the Hallicrafters SR-160. (No panel mounted Loading Capacitor.)



Another factor is the panel meter which will be mounted on the control panel in front of the RF Enclosure and above the Plate Tune control. It is all about clearances and space allocation.

Topside Space Allocation












Them that know can make things go! Yesterday was a very productive day!

Surprisingly there were lots of views of the Home Depot Biometric Surveillance issue. A nagging question, we all have, is the Biometric data collected by Home Depot and Others used only for Theft Deterrence and/or are ICE and DHS also getting a feed as a part of the alien roundup? There is no doubt you are being watched and if your immigration status is in question... Caveat Emptor!

73's
Pete N6QW

Thursday, August 28, 2025

The New Power Supply Test = Not as Expected!

In a nutshell, most likely overhyped and definitely underperforming. We as Americans, all of us, so much want to get "such a deal" and the Chinese play into that American weakness: Almost a deal but not quite the one we wanted

The supply never produced 300VDC but did hold at 280VDC all the way up to 70 MA of current draw. That 20-volt difference at 0.3 amps is 6 watts of power you won't see going into the 12GE5.

Shame on me as two of the comments on the product did spell out that deficiency, yet the supply has a high rating. Certainly not from me! How could I be so blind! Dire Straits said it best: Something for Nothing (But the Chicks are Free... BUT No Freebies Here). This supply might be a $1.25 Hooker disguised to look $2.50.



I did test this power supply on a CW transmitter to see how it holds up. It did OK with a 6L6 in the socket, where we saw 60 MA of Cathode current, and the Drake Wattmeter said 7 watts in 40M. I attribute the puny output to the lower Plate Voltage at 280VDC but with say 350 VDC or more on the plate I could conceivably see about 20 Watts output. (Do the math as 70X0.3 = 21 watts more input at a higher plate voltage.) The signal sounded clean and that was both the case on 7030 and 7060 kHz.





While my earlier tests (in the video) gave pause for the use of the supply on the Hybrid wireless, the CW tests suggest that it may possibly function on SSB in the Hybrid Wireless. That will have to be tested, but it is a disappointment that you can't get 300VDC out of the supply as advertised.

Them that know sometimes get fooled by the bright shiny object. I included some shots in the video of how I built the test fixture. The Manual Mill is sure a handy tool.

73's
Pete N6QW
 

Wednesday, August 27, 2025

Random Musings Today.

The watched pot never boils as the new DC power supply didn't arrive until about 7:30 PM last night so no testing until today. The size is deceiving as it is really small. 

At the first look, the Amazon bag looked too small. But sure, enough it was the supply. This is good news for making new compact equipment and/or retrofitting existing hardware. I hope it works as this small size aspect shows real promise. Even without a test, the terminals for the 6.3 volts say Ground and 6.3 Volts, thus most likely DC.

My post the other day netted a response from a blog reader with a link to a news article regarding Home Depot citing a lawsuit alleging video profiling customers during checkout. The basis of the suit is that this profiling is being done without notice to or permission from the customers. If this is a case my admonition about being watched is more than just a possibility and Home Depot may not be the Lone Ranger.

In our legal system (or it used to be) is the concept of innocent until proven guilty and the suit has applicability in the state where the suit was filed because of an existing law regarding collection of biometric data. That may not be the case in other states where there is no such law on the books. Bottom line "AI Watching Technology" is at a store near you.

The basis of facial Biometric collection is to thwart theft. Old school: you look like a thief so you must be one. Yet, just yesterday in Ventura County, where I live, 14 people were Busted for $10M in thefts from Home Depot.  Obviously, this will be a critical piece of defense for the Biometric data collection... The $10M theft is likely not a singular event but only a sample.

Suddenly the pieces are coming together about why the Home Depot salesclerk opened up the machine to validate I put $6 in the machine. True I hadn't shaved on Saturday, was wearing a KN-95 mask and had a ball cap on and must have looked "theify". BTW I still wear a mask at Covid breeding grounds like Home Depot, Costco and the Grocery Store. 

Yesterday while awaiting the power supply, I did fabricate the RF Cage that will be installed around the 12GE5 final RF amp circuitry. More real metal bashing.



Unabashedly I say you are being watched and profiled.

Them that know can make things go.

73's
Pete N6QW


In case you are keeping score...

 Interesting results... Iowa : Joni Ernst's Republican seat was won by Democrat Josh Turek. [senatordb.com] , [ballotpedia.org] Kansas :...