Wednesday, September 17, 2025
Advancing the Final Assembly of the Mostly Vacuum Tube Transceiver
Tuesday, September 16, 2025
Helpful Herman was lonely and so Copilot came up with Blondie
When I inputted to Copilot the specs for Blondie, I stipulated that her family roots should be eastern European (like the Ukraine), that she be around 25 and definitely shapely. Herman is Happy!
Monday, September 15, 2025
Meet Herman, my newly AI generated helper for the N6QW, Newbury Park Laboratories
Meet Totally AI Generated, Helpful Herman!
Sunday, September 14, 2025
Tidbits from Saturday and a visit to a ham event.
For the 1st time in 15 years, I attended a ham event at the campus of the California State University Channel Islands, a mere 3 miles from my QTH.
Saturday, September 13, 2025
Using AI as a design Tool. Caveat Emptor
The one "large" open item on the Hybrid Wireless is the final design for the 12GE5 Final RF Amp stage. It is also the only module not already fully built and tested.
Absolutely! Let’s walk through a practical design for a linear RF amplifier stage using the 12GE5 beam power tube, tailored for 7 MHz (40-meter band) operation in Class AB mode.
📐 Design Overview
✅ Tube Parameters
Tube: 12GE5 (beam power tetrode)
Plate Voltage (Vᵖ): 500 VDC
Screen Voltage (Vg2): 280 VDC
Grid Bias (Vg1): -30 VDC
Operating Frequency: 7 MHz
Mode: Class AB linear amplifier
⚙️ Circuit Design
1. Input Stage
Drive Requirement: ~10–15W RF input for full output
Input Matching: Use a tuned grid circuit with a low-Q parallel LC tank resonant at 7 MHz
Grid Leak Bias: Fixed bias via -30V supply, with 10kΩ grid resistor to ground
2. Plate Circuit
Load Impedance: For Class AB, target ~2.5–3.5 kΩ plate load
Tank Circuit: Series LC tuned to 7 MHz
DC Blocking: High-voltage capacitor (e.g., 1–2 kV rated, 1000 pF)
3. Pi-Network Output
Used to match the high plate impedance to a 50Ω load.
| Component | Typical Value (for 7 MHz) |
|---|---|
| C1 (tune cap) | 100–300 pF variable |
| L (coil) | ~2.5–3.5 µH (air-wound) |
| C2 (load cap) | 500–1000 pF variable |
Design Tip: Use a roller inductor or tapped coil for L, and vacuum variable capacitors for C1/C2 if high power is expected. (End of Output)
The response did say I should expect 30 to 35 watts PEP output with an efficiency of around 60%. The data above is very consistent with what I thought the values of the components and the tank circuit should be and the expected output.
Thursday, September 11, 2025
So be over with the old radios... A comment to me
Apologies for dwelling on the radios that never were. This is 2025 and many hams only want to see the New Stuff. So, I stop here.
Wednesday, September 10, 2025
Cosmophone 35. Commencing the Final Assembly Stage of the Hybrid Wireless.
For the unknowing there were Bi-Lateral SSB Transceivers predating the Bitx20 by some 50 years. Meet the Cosmophone 35.
Moving back to the N6QW Newbury Park Lab, now the Big Task... wiring all the stages together and building the 12GE5 RF Amp stage. I am delighted how the front panel turned out.
In case you are keeping score...
Interesting results... Iowa : Joni Ernst's Republican seat was won by Democrat Josh Turek. [senatordb.com] , [ballotpedia.org] Kansas :...
-
Cruise through the lower part of the ham bands bands and what do you hear? Well, FT-8 and CW. Often you will not hear any SSB stations yet g...
-
I am bristling over the thought that a person who has no prior license and/or knowledge of amateur radio in the span of 45 minutes can go fr...
-
Building a SSB Rig (Radio) in 2022 [A word Document of this total posting can be found here PLEASE NOTE this opens to the home page of my ...




















