Tuesday, September 9, 2025

The Great Great Grandfather of the ICOM IC-7300

A Quinquagenarian, this ICOM Radio started the revolution of products under the ICOM Banner leading today to the IC-7300 Mark II.


While you might be tempted to "buy it now" on eBay, look before you leap. The rig was a marvel for its time but today could be a nightmare of the 10th degree. 

ICOM used a whole series of relays to band change, and it may be impossible to find replacements. A replacement Encoder is another unobtanium item. 

In 1975 I actually twiddled an IC-701 knob but having a family, a mortgage and an XYL (God Rest her Soul) who hated ham radio... it never happened. But I was indeed awestruck!

Some items arrived yesterday, but of course not all the ones I needed. My #3 son, several years ago purchased and gave me a ton of Metric nuts, bolts and washers in various sizes. 

I have previously not used the goodies because the bolts heads need a hex Allen wrench for installation. I have an array of Allen and Bristol wrenches, but they are all small in size (FFS issue). Finally, I was forced to use the Metric stuff in keeping with the Wireless theme. I caved and bought these Wrenches which were in the stuff.


More small pieces of work yesterday and it is these small details which take lots of time. I worked a bit on the power supply thinking the 100Ufd @ 600VDC would show up from Digi-Key. Despite a call to them last Friday where I was assured my parts would be there on Monday. NOT!

Meter Changed from 500VDC to 1000VDC

Bridge Rectifier Assembly Diodes are 1N4007

Two items that were worked on the power supply was to change out the 500VDC Meter to 1000VDC. At 450VDC the original meter would be literally pinned, and the change of meter places the reading mid-scale. I bought the 1000VDC meter about 7 years ago and didn't think I would ever use it. But here it is being used. The other piece of power supply work involved installing the bridge diodes and the bleeder resistor.

I wanted to ensure that were no harmonics from the IRF510 stage and since we are not using a tuned grid circuit, it would be necessary to have a W3NQN filter following the IRF510 and ahead of the 12GE5. I found a suitable unit in my junk box.



In an extra-ordinary alignment of the stars there is but a short distance between the output of the Filter and the Grid input to the 12GE5. Lucky me.


More small detail stuff on dock for today, time consuming but necessary.

Them that know can make things go.

73's
Pete N6QW


Monday, September 8, 2025

Adding Cinnamon to the Spice! The Sideband Engineers SBE-35 and SBE-36.

Through my hands have passed many Sideband Engineers SBE-33 and SBE-34 Transceivers. Later on, the SBE-35 and SBE-36 appeared on the scene and those I believe were totally manufactured in Japan. 





I believe this restoration was done by W4OP, Dale.


I haven't personally seen an SBE-35 or the SBE-36 which had a Nixie tube display. It seems like the rigs didn't make much of a splash with the ham community at large. One issue of ergonomics, for me, is the Microphone Jack on the SBE-35 is very close to the tiny main tuning knob. With my FFS, I would be complaining a lot.

More time in the shop yesterday as I worked down my list and finished installing hardware on the back panel. 


Final Back Panel Installations

Starting on the left side we have the Antenna Jack; the Knob is on the pot that controls the Bias setting and to the right of that is the 8-pin Power Connector. The three RCA jacks from left to right, are the Fan Power, External Speaker and External Linear Amp control. Rounding out the installations was the Cooling Fan. The two bolts just to the right of the Antenna Jack tie into the shield enclosure for the 12GE5 Final RF Amp which stiffens the back panel so there is no movement. 


Anchoring the Back Panel!

I did a trial run on the Wireless bottom plate which is 8X12X1/8 inch. It fits perfectly which is a testament to all the front-end work to accurately cut the metal and double check all installations. I had some really large rubber feet which I will install to give it a solid support base.


Bottom Plate ~ Perfect Fit!


Rubber Feet on Bottom Plate.

With all of the metal and nuts and bolts, the Hybrid Wireless has gained a few pounds. Oh, I use a blue felt tip pen to mark various lines and dimensions then a rag doused with a touch of alcohol cleans everything up nicely.

I am awaiting the delivery of three special switches and those will be installed on the front panel but before I cut any metal I have to know their exact dimensions. With the area under the chassis being reduced that makes for tight dimensions below the main plate to install any controls in the space. Maybe Monday.

Them that know can make things go.

73's
Pete N6QW

Sunday, September 7, 2025

More Oldies that did not see Major Production! More Fabrication!

This rig had a very limited production run and never became a full product line. Coming out in 1975 it is solid state and noteworthy No Tune/Load/or Grid Drive Controls.



E F Johnson Avenger... NICE!

I could see myself owning one of these jewels. Perfect for small operating desks. Covers the 80, 40, 20, 15 and 10 Meters with USB/LSB and CW. Supposedly good for 150 watts and only a handful (I think around 25) were built. The above unit was up for auction on eBay about 18 years ago listed at $800. Gulp!

What a productive day yesterday as it was not too hot in the garage and we went down our to do list.



More Stuff Installed

My first concern was heat in the box as the main tube module is compact and we are installing this heat generator inside of a case. Thus, I planned for a fan installation. Two minutes with the Carbide Create Design Software and I had a CNC program to cut a three-inch circular hole in the back panel. About five minutes on the CNC and we have a fan port.


Fan Installation


Quiet & Cool!




Metal Cutting on the CNC

The next item was the front panel and the installation of 5 controls including locating and installing the hole for the Plate Tuning capacitor penetration. 



Tuning Cap Penetration.



Operational Control Installations

To be installed on the front panel are the Power Switch, USB/LSB Select and the MOX control. I have not installed the antenna connector and several RCA jacks as yet on the back panel. 

One of the back panel RCA jacks will be the power connector for the newly installed fan. That install will have a 100nF cap across the RCA jack.  For those who like to pick nits, I intend to install a piece of metal window screen between the back panel and the front face of the fan. This will assure continuous shielding.

Once all the metal bashing is done, we will start the connections to the built hardware and once finished performing a systems test that a QRP signal is coming out of the IRF510. Only then will I start the build of the 12GE5 stage. Chunking the tasks this way it leaves the only unknown as the 12GE5 stage

Them that know can make it go. Are you better off today with you know who?

73's
Pete N6QW

Saturday, September 6, 2025

Another Productive Day.

 

Underside Boards

Bias Pot Installed!

ESP32 Board mounted Vertically, Copper PC Board is a Shield

Installed the W3NQN LPF. TR Relay and Coax Connector will install on back wall 

As I work on this project save for the 12GE5 RF Amp stage, all the electronics are built! The real task is Milling, Drilling, Mechanical Engineering and Production Engineering. You have to have the final product configuration clearly in mind even before you start. This is a design build project!

W3NQN LPF's
(Thanks to the GQRP Club Data Sheets)





Them that know can make things go.

73's
Pete N6QW




Friday, September 5, 2025

Old Time "Vaporware" and More Build Stuff.

 

Gonset Mobile SSB Transceiver (Today's price $8673.45)

What a shock to spot advertising from some 65 years ago for products that I don't think actually made it to market. This is one of those products. In 1960 the MSB1 was half the price of a NIB 1960 VW Beetle. 

This was probably a trial balloon that quickly broke based on the price point given today that $8674 is a huge sum for a ham rig! Vaporware of the 1960's.

Note the different Front Panel = Mockup

So, they ran a few ads using a mockup and tested the market only to likely find that the market wasn't there for something costing so much. In a blink of an eye soon there were competing products costing half as much and fit a lot better in the family budget. 

The year 1960 was an exciting time reference as I was a freshman at Penn State, the Space Race was on, Cycle 19 was as hot as a Firecracker and of course many YL Coeds who were open to all sorts of adventures. So, who needs an $800 radio that wasn't even in production.

Yesterday was another productive day as I successfully built the back panel. 


Note: Angle Stock now on top of the main Mounting Plate




You have got to love it when a plan comes together!


Lots of measuring and measuring a second time. I also had to make a small U Turn as I had to reverse mount the main plate and that left less room on the back apron just below the plate level. 

Initially the angle stock was below the mounting plate and then reversed to above the main plate which had the effect of lowering the space under the main plate. So instead of the Jones Plug we went with a male type of octal socket. It was tight but we made it work. [Shades of 21.43 Stone Mary Jo. One Stone = 14 Pounds]

The reversal was to accommodate the Plate Tuning Cap shaft on the front panel giving about 0.5 inches of greater clearance.




Octal Power Plug Back Apron

Work planned for today is to cut angle stock for the very bottom edge of the front and back panels, cut holes in the back apron for the auxiliary audio output jack, locate the bias pot, antenna connector, ground post and external amp control jack.

Since the main mounting plate angle stock is now above the main plate, I need to notch the Final RF Amp shield assembly to account for the change.

Them that know can make things go.

Who are you kidding if you think that as a nation we are on the right course. Only the superrich must think that as their pockets get lined with even more riches. The jobs report out today provides more evidence that the jobs added were below expectations and the economy appears to be stalling. Hey majority pat yourself on the back, you voted for this. Are we headed for a recession?

73's
Pete N6QW

Thursday, September 4, 2025

From 1943 ~ How a vacuum tube works. More Progress.

An interesting You Tube video from 80 years ago on: How a Vacuum Tube Works. It's short but lays out the fundamentals of operation of a Triode Vacuum Tube. Cool Beans.

Test Panel Cut Out

More fundamental work yesterday and I made a trial run cut of the two large rectangular panel cut outs and tweaked my CNC program a bit to account for a larger diameter end mill and this should result in a tighter fit of the ILI9341 Display and the 0 to 200Ma Meter. 

A Tight Fit is best described as the 21.43 Stone Mary Jo in the back seat of the 57 VW Beetle after consuming three Bob's Boy Hamburgers from his burger joint located near the Monroeville Miracle Mile Mall. 

Yes, Three of these delights!


Cleaned Up the ESP32 Digital LO/BFO Module

Mounted the Front Panel to the Plate

Front Panel Meter Cut Out

Installed the Color TFT, Meter & Encoder

Whew what a day for installations and finalizing a place for everything and everything in its place. Without a doubt vast experience and tribal knowledge accounted for today's progress. Things are coming together nicely. Lots of measuring before any cutting!

Today's work involves the drilling of the back panel. There are many installations to accommodate on the back panel including the Jones plug, the antenna connector, an auxiliary speaker output jack, ground terminal and external amplifier jack.  Many of the mounting holes duplicate those of the front panel and I will use the front panel as an overlay drilling template.

Them that know can make things go. 

73's
Pete N6QW






Wednesday, September 3, 2025

A Very Productive Day.

[News Flash Jameco Electronics is now distributing Hammond Products including selected Peter Dahl Plate Transformers for those Big Tube amps and power transformers for guitar amps.]


I started at 8AM and stopped at 1:30PM when it was just too hot to remain in the garage, but again great progress.



A Whole Lot of Holes!

The mounting plate has so many holes and is so "holey", it may qualify as a very Catholic mounting plate. 

The hole placement was based on our initial allocation of space on the top and bottom sides of the mounting plate. The board layout fairly well followed our original placement plan. Behind this was attention to the actual mounting holes so they do not end up in the middle of a board on the opposite side. I used a lot of 1/4-inch threaded spacers and even countersunk bolt heads.





Topside: Main Board. ESP32 LO/BFO and BPFs


Bottom side of Mounting Plate

On the bottom side, four boards were installed including the Power Board @ 1 O'clock, Audio Amp at 6 O'clock, Driver at 9 O'clock and IRF510 at 11 O'clock.

One or two more boards will be installed including the LPF Board and the TR Relay Board.

Trial Mounting of the Cathode Meter

I also did a trial run on creating the hole cut out for the Cathode meter. It was an ugly experience. It may be really difficult to do on a thick aluminum panel. A possibility is to just make a rectangular hole in the Front Panel and then poke the meter through that hole and using this assembly just affix it to the back side of the panel. Rectangular holes are easier than the round and this is already built.

A huge step forward. Them that know can make things go. You are being watched, and something is afoot in Washington likely not good news for most of us. For the majority who pulled the lever, after 9 months in play, is this the outcome you expected?

73's
Pete N6QW





In case you are keeping score...

 Interesting results... Iowa : Joni Ernst's Republican seat was won by Democrat Josh Turek. [senatordb.com] , [ballotpedia.org] Kansas :...